Manual Dimplex SIH 20TE (page 26 of 56) (English, German, French)

520399

Zoom out

Zoom in

1/56

EN-10 452234.66.77 · FD 9912 www.gdts.one

English SIH 20TE

7.5.3 Connecting an electronically

regulated circulating pump

Electronically regulated circulating pumps have high starting

currents, which may shorten the service life of the heat pump

manager. For this reason, a coupling relay is installed or must be

installed between the output of the heat pump manager and

the electronically regulated circulating pump. This is not neces-

sary if the permissible operating current of 2 A and a maximum

starting current of 12 A are not exceeded in the electronically

regulated circulating pump or if express approval has been is-

sued by the pump manufacturer.

ATTENTION!

It is not permitted to connect more than one electronically

regulated circulating pump via a relay output.

8 Commissioning

8.1 General Information

To ensure proper commissioning it should be carried out by a

customer service authorised by the manufacturer. These meas-

ures can also include an additional warranty under certain con-

ditions (see Warranty).

8.2 Preparatory Steps

Prior to commissioning, the following items need to be

checked:

All connections of the heat pump must have been made as

described in Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The strainer must have been fitted in the sole inlet of the

heat pump.

In the brine and heating circuits all valves that might impair

the proper flow must be open.

The settings of the heat pump controller must be adapted

to the heating installation in accordance with the instruc-

tions contained in the controller's operating manual.

8.3 Commissioning Procedure

The heat pump is commissioned via the heat pump manager.

ATTENTION!

Start-up must be performed in accordance with the

installation and operating instructions of the heat pump

manager..

9 Care/Cleaning

9.1 Care

To prevent malfunctions due to sediments in the heat exchang-

ers, care must be taken that no im-purities can enter the heat

source system and the heating installation. In the event that op-

erating malfunctions due to contamination occur nevertheless,

the system should be cleaned as described below.

9.2 Cleaning of Heating Side

The ingress of oxygen into the heating water circuit, in particu-

lar if it contains steel components, may result in the formation

of oxidation products (rust). These can enter the heating system

via valves, circulating pumps or plastic tubing. It is therefore im-

portant - in particular with respect to the piping of underfloor

heating systems - that the installation be executed in a diffu-

sion-proof manner.

ATTENTION!

To prevent the accumulation of deposits (e.g. rust) we

recommend using a suitable corrosion protection system.

In the case of severe contamination leading to a reduction in

the performance of the condenser in the heat pump, the sys-

tem must be cleaned by a heating technician.

Based on current information, we recommend using a 5 %

phosphoric acid solution for cleaning purposes. However, if

cleaning needs to be performed more frequently, a 5 % formic

acid solution should be used.

In either case, the cleaning fluid should be at room tempera-

ture. It is recommended that the heat exchanger be cleaned in

the direction opposite to the normal flow direction.

To prevent acidic cleaning agents from entering the circuit of

the heating installation we recommend that the flushing device

be fitted directly to the supply and return lines of the condenser

of the heat pump.

Thereafter the system must be thoroughly flushed using appro-

priate neutralising agents in order to prevent any damage

caused by cleaning agent residues that may still be present in

the system.

All acids must be used with great care, all relevant regulations

of the employers' liability insurance associations must be ad-

hered to.

The manufacturer's instructions regarding cleaning agent must

be complied with at all times.

9.3 Cleaning of Heat Source Side

ATTENTION!

The supplied strainer must be fitted in the heat source inlet of

the heat pump in order to protect the evaporator against the

ingress of impurities.

The filter sieve of the dirt trap should be cleaned one day after-

start- up. Further checks must be set according to the level of-

dirt.If no more signs of contamination are evident, the filter can

be removed to reduce pressure drops.

The manual says there is a modbus and ethernet option. Is there a list of modbus registers available? Submitted on 14-1-2022 at 12:40
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SIH 20TE in the language / languages: English, German, French as an attachment in your email.

The manual is 1.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex SIH 20TE

Dimplex SIH 20TE Usermanual and installation guide - Dutch - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SIH 20TE Manual

Product: