Manual Dimplex SI 85TUR (page 28 of 64) (English, German, French)

798446

Zoom out

Zoom in

1/64

EN-10 452237.66.56 · FD 9912 www.gdts.one

English SI 85 TUR

7.6 Electrical connection

7.6.1 General

All electrical installation work must be carried out by a trained

electrician or a specialist for the specified tasks in accordance

with the

installation and operating instructions,

country-specific installation regulations (e.g. VDE 0100),

technical connection conditions of the energy suppliers

and supply grid operators (e.g. TAB) and

local conditions.

To ensure that the frost protection function of the heat pump

works properly, the heat pump manager must remain con-

nected to the power supply and the flow must be maintained

through the heat pump at all times.

The switching contacts of the output relay are interference-

suppressed. Therefore, depending on the internal resistance of

the measuring instrument, a voltage can also be measured

when the contacts are open. However, this will be much lower

than the line voltage.

Extra-low voltage is applied on the controller terminals N1-J1 to

N1-J11; N1-J19; N1-J20; N1-J23 to N1-J26; N17-J1 to N17-

J4; N17-J9; N17-J10; N0-J2 to N0-J14 and the terminal strips

X3 and X5.1. If, due to a wiring error, the line voltage is mistak-

enly connected to these terminals, the heat pump manager will

be destroyed.

7.6.2 Electrical installation work

1) The 4-core electrical supply cable for the output section of

the heat pump is fed from the heat pump meter via the util-

ity company blocking contactor (if required) into the heat

pump.

Connection of the mains cable to the contact plate of the

heat pump via terminals X1: L1/L2/L3/PE.

An all-pole disconnecting device with a contact gap of at

least 3 mm (e.g. utility blocking contactor or power contac-

tor) and an all-pole circuit breaker with common tripping

for all external conductors must be installed in the power

supply for the heat pump (tripping current and characteris-

tic in compliance with the device information).

ATTENTION!

Ensure the rotary field is clockwise when connecting the

mains cables (if the rotary field is not clockwise, the heat

pump will not work properly, is very loud and may cause

damage to the compressor).

2) The 3-core electric supply cable for the heat pump man-

ager (heating controller N1) is fed into the heat pump.

Connection of the control cable to the contact plate of the

heat pump via terminal X2: L/N/PE.

Details on the power consumption of the heat pump are

listed on both the product information sheet and the type

plate.

The supply cable (L/N/PE~230 V, 50 Hz) for the heat pump

manager must have a continuous voltage. For this reason,

it should be tapped upstream from the utility blocking con-

tactor or be connected to the household current, because

otherwise important protection functions could be lost

during a utility block.

3) The utility blocking contactor (K22) with 3 main contacts

(1/3/5 // 2/4/6) and an auxiliary contact (NO contact 13/

14) should be dimensioned according to the heat pump

output and must be supplied on-site.

The NO contact of the utility blocking contactor (13/14) is

looped from terminal strip X3/G to controller N1/J5-ID3.

CAUTION! Extra-low voltage!

4) The contactor (K20) for the immersion heater (E10) of

mono energy systems (HG 2) should be dimensioned ac-

cording to the radiator output and must be provided on-

site. It is controlled (230 V AC) from the heat pump man-

ager via terminals X2/N and contact N1/J13-NO4 on the

heat pump manager.

5) The contactor (K21) for the flange heater (E9) in the do-

mestic hot water cylinder should be dimensioned accord-

ing to the radiator output and must be provided on-site. It

is controlled (230 V AC) from the heat pump manager via

terminals X2/N and contact N1/J16-NO10.

6) The contactors mentioned above in points 3, 4 and 5 are

installed in the electrical distribution system. Mains cables

for installed heating systems must be designed and pro-

tected in accordance with the valid standards and regula-

tions.

7) All installed electric cables must have permanent wiring.

8) The heat circulating pump (M13) is activated via the con-

tact N1-J13/NO5. Connection points for the pump are

coupling relays KM13/14 and X2/N.

9) The auxiliary circulating pump (M16) is activated via the

contact N1-J16/NO9. Connection points for the pump are

coupling relays KM16/14 and X2/N.

10) The domestic hot water circulating pump (M18) is acti-

vated via the contact N1-J13/NO6. Connection points for

the pump are coupling relays KM18/14 and X2/N.

11) The brine or well pump (M11) is activated via the contact

refrigeration circuit controller N0/J18-Out3. A coupling

relay is already integrated in this output. If an additional

well pump is used, the protective motor switch at the site

must be checked and replaced if necessary.

Ensure that the power supply for these terminals cannot be

switched off by the tariff contactor when connecting the

mains cable for the well pump, in order to safeguard the

switch-off delay of the well pump.

12) A return sensor is integrated into the heat pumps. The de-

mand sensor must be installed in the immersion sleeve in

the manifold only when a dual differential pressureless

manifold is used. The single-core wires are then connected

to terminals X3/GND and controller N1/J2-U2.

13) The external sensor (R1) is connected to terminals X3/GND

and controller N1/J2-U1.

14) The domestic hot water sensor (R3) is included with the

domestic hot water cylinder and is connected to terminals

X3/GND and controller N1/J2-U3.

15) The connector cable (or the connector) of the hydraulic 4-

way reversing valve must be connected to the receptacle

of the device mounted at the "top" in the rear wall.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 85TUR in the language / languages: English, German, French as an attachment in your email.

The manual is 5.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SI 85TUR Manual

Product: