Manual Dimplex SI 7ME (page 23 of 56) (English, German, French)

798212

Zoom out

Zoom in

1/56

www.dimplex.de 452232.66.13 · FD 9603 EN-9

English

SI 5ME - SI 14ME

8 Commissioning

8.1 General Information

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorised by the

manufacturer. These measures can also include an additional

warranty under certain conditions (see Warranty).

8.2 Preparation

The following items need to be checked prior to start-up:

The heat pump must be fully connected, as described in

Chapter 7.

The heat source system and the heating circuit must have

been filled and checked.

The dirt trap must be inserted in the brine inlet of the heat

pump.

All valves that could impair proper flow in the brine and heat-

ing circuits must be open.

The heat pump manager must be adapted to the heating

system in accordance with the controller’s operating instruc-

tions.

8.3 Start-up Procedure

The heat pump is started up via the heat pump manager.

ATTENTION!

The heat pump must be started up in accordance with the installation and

operating instructions of the heat pump manager.

If an overflow valve is fitted to assure the minimum heating water

flow rate, the valve must be set in accordance with the require-

ments of the respective heating system. Incorrect adjustment

can lead to faulty operation and increased energy consumption.

We recommend carrying out the following procedure to correctly

adjust the overflow valve:

Close all of the heating circuits that may also be closed during

operation (depending on the type of heat pump usage) so that

the most unfavourable operating state - with respect to the water

flow rate - is achieved. This normally means the heating circuits

of the rooms on the south and west sides of the building. At least

one heating circuit must remain open (e.g. bathroom).

The overflow valve should be opened far enough to produce the

maximum temperature spread between the heating flow and re-

turn flow listed in the table below for the current heat source tem-

perature. The temperature spread should be measured as close

as possible to the heat pump. The heating element of mono en-

ergy systems should be disconnected during start-up.

9 Maintenance and

Cleaning

9.1 Maintenance

To prevent faults due to sediment in the heat exchangers, care

must be taken to ensure that no impurities can enter either the

heat source system or the heating system. In the event that op-

erating malfunctions due to contamination occur nevertheless,

the system should be cleaned as described below.

9.2 Cleaning the Heating System

The ingress of oxygen into the heating water circuit may result in

the formation of oxidation products (rust), particularly if steel

components are used. This oxygen enters the heating system via

the valves, the circulating pumps and/or plastic pipes. It is there-

fore essential - in particular with respect to the piping of under-

floor heating systems - that only diffusion-proof materials are

used.

NOTE

We recommend the installation of a suitable corrosion protection system

to prevent the formation of deposits (e.g. rust) in the condenser of the

heat pump.

Residue from lubricants and sealants may also contaminate the

heating water.

In the case of severe contamination leading to a reduction in the

performance of the liquifier in the heat pump, the system must be

cleaned by a heating technician.

Based on current knowledge, we recommend carrying out the

cleaning with a 5 % phosphor acid or, if more frequent cleaning

is required, with a 5 % formic acid.

In either case, the cleaning fluid should be at room temperature.

We recommend flushing the heat exchanger in the direction op-

posite to the normal flow direction.

To prevent acidic cleaning agents from entering the heating sys-

tem circuit, we recommend connecting the flushing device di-

rectly to the flow and return flow of the liquifier. It is important that

the system be thoroughly flushed using appropriate neutralising

agents to prevent any damage from being caused by cleaning

agent residue remaining in the system.

Acids must be used with great care and all relevant regulations of

the employers’ liability insurance associations must be adhered

to.

The manufacturer's instructions regarding cleaning agent must

be complied with at all times.

9.3 Cleaning the Heat Source

System

NOTE

The supplied dirt trap must be inserted in the heat source inlet of the heat

pump to protect the evaporator against the ingress of impurities.

The filter sieve of the dirt trap should be cleaned one day after-

start- up. Further checks must be set according to the level of

dirt.If no more signs of contamination are evident, the filter can

be removed to reduce pressure drops.

Heat source

temperature

Max. temperature spread

between heating flow and return

flow

From To

-5 °C 0 °C 10 K

1°C 5°C 11 K

6 °C 9 °C 12 K

10 °C 14 °C 13 K

15 °C 20 °C 14 K

21 °C 25 °C 15 K

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 7ME in the language / languages: English, German, French as an attachment in your email.

The manual is 2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex SI 7ME

Dimplex SI 7ME Usermanual and installation guide - Dutch - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SI 7ME Manual

Product: