Manual Dimplex SI 50ZS (page 16 of 48) (English, German, French)

798456

Zoom out

Zoom in

1/48

E-6

English

9 Care/Cleaning

9.1 Care

The heat pump is maintenance-free. To prevent malfunctions

due to sediments in the heat exchangers, care must be taken

that no im-purities can enter the heat source system and the

heating installation. In the event that operating malfunctions due

to contamination occur nevertheless, the system should be

cleaned as described below.

9.2 Cleaning og Heating Side

The ingress of oxygen into the heating water circuit, in particular

if it contains steel components, may result in the formation of ox-

idation products (rust). These can enter the heating system via

valves, circulating pumps or plastic tubing. It is therefore impor-

tant - in particular with respect to the piping of underfloor heating

systems - that the installation be executed in a diffusion-proof

manner.

ATTENTION!

To prevent the accumulation of deposits (e.g. rust) we recommend using

a suitable corrosion protection system.

In the case of severe contamination leading to a reduction in the

performance of the condenser in the heat pump, the system must

be cleaned by a heating technician.

Based on current knowledge, we recommend cleaning with a

5% phosphoric acid solution or, in the case that cleaning needs

to be performed more frequently, with a 5% formic acid solution.

In either case, the cleaning fluid should be at room temperature.

It is recommended that the heat exchanger be cleaned in the di-

rection opposite to the normal flow direction.

To prevent acidic cleaning agents from entering the circuit of the

heating installation we recommend that the flushing device be fit-

ted directly to the supply and return lines of the condenser of the

heat pump.

Thereafter the system must be thoroughly flushed using appro-

priate neutralising agents in order to prevent any damage caused

by cleaning agent residues that may still be present in the sys-

tem.

All acids must be used with great care, all relevant regulations of

the employers' liability insurance associations must be adhered

to.

If in doubt, contact the manufacturer of the chemicals!

9.3 Cleaning of Heat Source Side

ATTENTION!

The supplied strainer must be fitted in the heat source inlet of the heat

pump in order to protect the evaporator against the ingress of impurities.

The filter screen of the strainer should be cleaned one day after

commissioning, thereafter every week. If no more contamination

can be noticed any more, the strainer filter can be removed in

order to reduce pressure losses.

10 Malfunctions /

Troubleshooting

This heat pump is a quality product and designed for trouble- and

maintenance-free operation. In the event that a malfunction oc-

curs nevertheless, it will be indicated on the display of the heat

pump controller. Simply consult the Malfunctions and Trouble-

shooting table contained in the in-stallation and operating man-

ual of the heat pump controller (manager).

If you cannot correct the malfunction yourself, please contact the

after-sales service agent in charge.

ATTENTION!

All work on the heat pump may only be performed by an authorised an

qualified after-sales service.

ATTENTION!

Disconnect all electrical circuits from the power supply before opening

the enclosure.

11 Decommissioning /

Disposal

Before removing the heat pump, disconnect the unit from the

power source and close all valves.

Environment-relevant requirements regarding the recovery, re-

cycling and disposal of service fuels and components in accord-

ance with all relevant standards must be adhered to. Particular

attention must hereby be paid to the proper disposal of refriger-

ants and refrigeration oils.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 50ZS in the language / languages: English, German, French as an attachment in your email.

The manual is 2.58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SI 50ZS Manual

Product: