Manual Dimplex SI 35TUR (page 23 of 56) (English, German, French)

798433

Zoom out

Zoom in

1/56

www.glendimplex.de 452237.66.54a · FD 0110 EN-7

SI 35TUR English

7.4.2 Mounting the outside temperature

sensor

The temperature sensor must be mounted in such a way that all

weather conditions are taken into consideration and the meas-

ured value is not falsified.

Mount on the external wall on the north or north-west side

where possible

Do not install in a "sheltered position" (e.g. in a wall niche or

under a balcony)

Not in the vicinity of windows, doors, exhaust air vents, ex-

ternal lighting or heat pumps

Not to be exposed to direct sunlight at any time of year

7.4.3 Installing the strap-on sensor

It is only necessary to mount the strap-on sensors if they are in-

cluded in the scope of supply of the heat pump but have not yet

been installed.

The strap-on sensors can be fitted as pipe-mounted sensors or

installed in the immersion sleeve of the compact manifold.

Mounting as a pipe-mounted sensor

Remove paint, rust and scale from heating pipe.

Coat the cleaned surface with heat transfer compound (ap-

ply sparingly).

Attach the sensor with a hose clip (tighten firmly, as loose

sensors can cause malfunctions) and thermally insulate.

7.4.4 Hydraulic distribution system

The compact manifold and the dual differential pressureless

manifold function as an interface between the heat pump, the

heating distribution system, the buffer tank and, in some cases,

even the domestic hot water cylinder. A compact system is

used to simplify the installation process, so that a lot of different

components do not have to be installed individually. Further in-

formation can be found in the relevant installation instructions.

Compact manifold

The return sensor can remain in the heat pump, or should be in-

stalled in the immersion sleeve. The remaining empty space be-

tween the sensor and the immersion sleeve must be filled com-

pletely with heat transfer compound.

Dual differential pressureless manifold

In order for the heating circuit pumps of the generator and con-

sumer circuits to supply the flow to the return sensor, this must

be installed in the immersion sleeve of the dual differential

pressureless manifold.

7.5 Electrical connection

7.5.1 General

All electrical installation work must be carried out by a trained

electrician or a specialist for the specified tasks in accordance

with the

installation and operating instructions,

country-specific installation regulations (e.g. VDE 0100),

technical connection conditions of the energy suppliers

and supply grid operators (e.g. TAB) and

local conditions.

To ensure that the frost protection function of the heat pump

works properly, the heat pump manager must remain con-

nected to the power supply and the flow must be maintained

through the heat pump at all times.

The switching contacts of the output relay are interference-

suppressed. Therefore, depending on the internal resistance of

the measuring instrument, a voltage can also be measured

when the contacts are open. However, this will be much lower

than the line voltage.

Extra-low voltage is applied to controller terminals N1-J1 to N1-

J11; N1-J19; N1-J20; N1-J23 to N1-J26; N17-J1 to N17-J4;

N17-J9; N17-J10; N0-J2 to N0-J14 and the terminal strips X3

and X5.1. If, due to a wiring error, the line voltage is mistakenly

connected to these terminals, the heat pump manager will be

destroyed.

Dimensioning parameter sensor lead

Conductor material Cu

Cable-length 50 m

Ambient temperature 35 °C

Laying system B2 (DIN VDE 0298-4 /

IEC 60364-5-52)

External diameter 4-8 mm

Hose clip

Strap-on sensor

Thermal insulation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SI 35TUR in the language / languages: English, German, French as an attachment in your email.

The manual is 1.57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SI 35TUR Manual

Product: