Manual Dimplex OFC1200 (page 4 of 4) (English)

798096

Zoom out

Zoom in

1/4

when the room is warm. To set the temperature required, turn the thermostat

knob clockwise until the required setting is reached. Alternatively to heat a

cold room quickly, turn the thermostat knob up fully. When the room has

reached the desired temperature, turn the thermostat knob anti-clockwise

until the thermostat just clicks off. The heater will now automatically operate

at this temperature.

The thermostat also has a frost protection setting marked ‘ ’. This setting is

useful in areas such as garages, to prevent frost damage. If the thermostat

is set to its minimum setting ‘ ’, the heater will cycle on and off to maintain

a temperature of approximately 5° to help protect against frost.

Note: Should the heater fail to come on when the thermostat is at a low

setting, this may be due to the room temperature being higher than the

thermostat setting.

Heat Selector Switches (see Fig.5)

Selector switches located on the control panel provide a choice of heat output

to suit varying conditions and for economy of operation.

Table 1

Model Switch Switch

OFC1200/OFC1200TI 650W 1200W

OFC1500/OFC1500TI/OFC1500TIF 800W 1500W

OFC2000/OFC2000TI 1100W 2000W

OFC2400/OFC2400TI/OFC2400TIF 1200W 2400W

Fan Heater (see Fig.6)

To accelerate room heating, a fan heater with a selector switch (S1) can be

switched on.

Digital Timer Operation (see Fig.7)

MPORTANT: Remember to observe all safety warnings when operating the

heater on auto setting, either attended or unattended.

The timer allows you to select ‘AUTO’ or ‘MAN ON’ by pressing the ‘MODE’

button until the required MODE appears at the bottom of the timer display.

‘MAN OFF’ MODE heat is permanently off. This is also the default screen.

‘MAN ON’ MODE allows power to the heater uninterrupted by the program

settings.

‘AUTO DLY’ switches the heater ON and OFF every day according to a set

daily program.

‘AUTO BLK’ switches the heater ON and OFF according to a set of programs

for weekdays only or weekends only.

Initial Operation

Note: Timer Memory Back Up Batteries – Once the heater has been left

plugged in with the socket switched on for at least 72 hours the timer’s

memory back up batteries will be fully charged.

In the event of a power cut or disconnection from the mains, the timer

will continue to function and all programmed settings will be retained

for up to six months providing the timer batteries are fully charged.

If however the timer batteries have not been charged fully, or if the

heater is deprived of power for longer than six months, then the time

and programme settings are likely to be lost and you may therefore need

to reset the time and programme before using the ‘AUTO’ MODE again.

For initial use, plug the heater into a regular household power point and turn

the power on. The timer is now ready to be set up for use.

Setting Time

1. Press the ‘PROGRAM’ button ONCE. The clock symbol appears on the

top left hand side of the screen. The user can now set the clock.

2. The hour digit will ash. To adjust the hour use the ‘-‘ & ‘+’ buttons. Conrm

the hour digit by pressing ‘ENTER’.

3. Once ‘ENTER’ has been pressed the minutes will ash. To adjust the

minutes use the ‘-‘ & ‘+’ buttons. Conrm the minute digit by pressing ‘ENTER’.

4. The timer now returns to the default display.

5. To reset incorrect time, repeat previous steps.

Once the correct time is set, a total of four ON/OFF time programs can be

set for operation.

Setting Programmes

OPTION 1; Daily (‘DLY’ on display): This is a daily program function, Monday

to Sunday with four ON/OFF program options available.

OPTION 2; Block (‘BLK’ on display): This is a block program function, Monday

to Friday with four ON/OFF program options or Saturday to Sunday with four

ON/OFF program options.

Press the ‘PROGRAM’ key twice to set the programs starting with ‘Daily

ON’ P1.

Setting P1 On Time

1. To set the hour use the ‘-’ & ‘+’ buttons. Conrm the hour digit by pressing

ENTER.

2. To set the minutes use the ‘-’ & ‘+’ buttons. Conrm the minute digit by

pressing ENTER.

Note: The minutes can only be set in 10 minute blocks.

Setting P1 Off Time

3. To set the hour use the ‘-’ & ‘+’ buttons. Conrm the hour digit by pressing

ENTER.

4. To set the minutes use the ‘-’ & ‘+’ buttons. Conrm the minute digit by

pressing ENTER.

Repeat steps 1 to 4 to programme P2, P3 and P4. After programming P4

you automatically enter the BLOCK programme option. Repeat steps 1 to 4

to programme P2, P3 and P4. After programming P4 you automatically exit

the BLOCK programme option.

At any time while programming the timer you can press the PROGRAM button

to exit to the default display.

NOTE: You can cycle quickly from daily mode to block modes by pressing

the MODE button.

The Advance Function

When in AUTO MODE, if the ‘+’ button is pressed for longer than 2 seconds

the programme will ADVANCE to the next setting programmed and will

only revert back to the program when the subsequent programme time is

reached. When the ADVANCE function is running the ADVANCE segment

will be displayed on the LCD screen. If the ‘-‘ button is pressed for longer

than 2 seconds when the ADVANCE programme is running the ADVANCE

feature will automatically be cancelled and the programme will run as normal.

e.g. If the present time is 14:00 and P1 ON is at 17:00 and P1 OFF is 19:00,

if ‘+’ is held for 2 seconds and remains on until 19:00. ADVANCE disappears

from the screen at 17:00 as set program is then running.

Key Lock

To lock the keypad press ENTER and MODE simultaneously. The key symbol

will appear on the screen when the keypad is locked. To unlock the keypad

repeat the action above.

Safety in use

This appliance incorporates a number of safety devices. In addition to the

‘Important Safety Advice’ section your attention is drawn to the following;

Tilt Switch

The tilt switch will prevent the heater from working if it is accidentally tipped

over on its side. If the radiator is tipped over while it is hot, disconnect the

power and allow it to cool, then stand the radiator back upright. Reconnect

the power - normal operation should be resumed.

Safety Overheat Protection

The heater is tted with a thermal safety cut-out which will switch off the heater

should it overheat for any reason. If the cut-out operates it is the result of

abnormal overheating, and customer services should be contacted for further

advice - see ‘After Sales Service’.

Storage

If the radiator is not required for long periods, for example during the summer,

it should be stored in a dry place and preferably covered to prevent the

accumulation of dirt and dust. The supply cord should be neatly coiled around

the cable wrap (see Fig. 1) and the plug should be inserted in to the plug pin

holes provided in the cable wrap.

IMPORTANT

Prolonged storage/mains disconnection periods may cause the timer to lose its

programmed settings and may require reprogramming, see initial operation

Cleaning

WARNING:ALWAYS DISCONNECT THE POWER SUPPLY BEFORE

CLEANING THE HEATER.

Do not use detergents, abrasive cleaning powder or polish of any kind on the

body of the heater. Allow the heater to cool, then wipe with a dry cloth to remove

dust and a damp cloth (not wet) to clean off stains. Be careful not to allow

moisture in to the heater.

Recycling

For electrical products sold within the European Community. At the

end of the electrical products useful life it should not be disposed

of with household waste. Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling advice

in your country.

After Sales Service

Should you require after sales service or should you need to purchase any

spares, please contact the retailer from whom the appliance was purchased.

Please do not return a faulty product to us in the rst instance as this may

result in loss or damage and delay in providing you with a satisfactory service.

The ns of this heater are lled with a precise quantity of special oil. Repairs

requiring opening of the oil container are only to be made by the manufacturer

or its service agent. For further advice if an oil leak is suspected please contact

the retailer from whom the appliance was purchased. Regulations concerning

the disposal of oil when scrapping the appliance must be followed. Please

retain your receipt as proof of purchase.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex OFC1200 in the language / languages: English as an attachment in your email.

The manual is 1.89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex OFC1200 Manual

Product: