Manual Dimplex MK1 (page 2 of 12) (English, German, Dutch, French)

798053

Zoom out

Zoom in

1/12

93mm

305mm

Energy Related Product Directive

Type of heat output/ room temperature control

With electronic room temperature control Yes

Electronic room temperature control plus week

timer Yes

With open window detection Yes

Model Identiﬁer(s):

B075E C100E D150E E200E

Nominal heat

output Pnom 0.75 kW 1 kW 1.25 kW 1.5 kW

Height (mm)

659 659 659 659

Width (mm)

570 840 1105 1373

Depth (mm)

50 50 50 50

Minimum heat

output (indicative) Pmin 0.75 kW 1.00 kW 1.25 kW 1.5 kW

Maximum continu-

ous heat output Pmax,c 0.75 kW 1.00 kW 1.25 kW 1.5 kW

Auxiliary electricity Consumption

At nominal heat

output elmax 0.00 0.00 0.00 0.00

At minimum heat

output elmin 0.00 0.00 0.00 0.00

In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005

With open window detection Yes

This product complies with Lot20 of the Energy Eciency Directive (2015/1188)

General Information

Please read the instructions closely before ﬁrst using the product.

The necessary wall mounting brackets are provided with the product as a

standard.

It should only be operated when in the upright position as shown - see Fig.1.

All models are IP20 rated. Before connecting the heater check that the supply

voltage is the same as that stated on the heater.

For further information on heater guards, please contact our guard supplier

direct on Tel. No. 020 7987 1184 or visit www.aianos.co.uk, or in case of diculty

or for further advice contact the Customer Helpline.

Wall Mounting

IMPORTANT - The radiator must only be mounted using the kit supplied

WARNING - This product is heavy and care should be taken in installation

Select a suitable position on a wall, near to a mains power outlet. The radiator

should not be mounted closer than 75mm from the ﬂoor - see Fig. 2 (to enable

cleaning), or adjacent side walls. Ensure at least 305mm clear space between

the radiator and any overhanging shelf. It should not be mounted closer than 1

metre from the ceiling.

STEP 1: Check that you have all the necessary components:

(a) 2 x Bottom wall brackets

(b) 2 x Top wall brackets

(d) 2 x Self-tapping screws.

STEP 2: Using a straight edge, draw a horizontal line (see ‘Y’ in Fig. 2) for the

bottom brackets at the required mounting height from the ﬂoor.

75mm

(min)

‘C’

‘Y’

75mm

(min)

Fig. 2

Fig. 3

Fig. 4 Fig. 5

Electrical Connection

Place the bottom brackets centrally over these centres with the top row of holes

on the line, and mark the ﬁxing hole positions – see Fig. 2.

STEP 3: Drill the holes and ﬁt wall plugs. Screw the bottom brackets in position

– see Fig. 2.

STEP 4: Measure dimension D in Fig. 1 according to model, from the top of the

bottom brackets and draw a horizontal line. Mark o the ﬁxing centres for the

top brackets in line with the bottom brackets. Place each top bracket on the

line and mark the ﬁxing holes – see Fig. 3. Drill and plug the wall and ﬁx the

top brackets in place.

STEP 5: Place the radiator on the bottom brackets, then ﬁt each securing

bracket to the top of the radiator and secure it with the self-tapping screw

provided – see Fig. 4.

Check that the radiator is securely ﬁxed to the wall.

This guide is for quick reference only

To view the full manual, please visit - www.dimplex.nl

NOTE - The bottom of the radiator must not be less than 75mm from the

ﬂoor. To achieve this the top edge of the bottom brackets must be at least

160mm from the ﬂoor - see Fig 2. On this line, mark o the ﬁxing centres

according to model - see `C’ in the table in Fig. 1 and Fig. 2

IMPORTANT - For safe clearances from shelf/obstacle - see Fig. 5

(max)

(min)

The electrical installation must be carried out by a competent electrician,

and be in strictaccordance with the current I.E.E. Regulations for Electrical

Equipment in Buildings. The wires in this mains lead are coloured in accordance

with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

The heater is ﬁtted with a length of ﬂexible cable type H05VV-F size 3 x

1.0mm2 for connection to the ﬁxed wiring of the premises through a suitable

connection box positioned adjacent to the heater.

A means for disconnection must be incorporated in the ﬁxed wiring of the

premises in accordance with the wiring rules. The supply circuit to the heater

must incorporate a double pole isolating switch having a contact separation

of at least 3mm.

WARNING - THIS APPLIANCE MUST BE EARTHED

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex MK1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex MK1 Manual

Product: