Manual Dimplex LA 11MSR (page 19 of 48) (English, German, French)

798188

Zoom out

Zoom in

1/48

www.dimplex.de 452158.66.28 · FD 9402 EN-7

English

LA 11MSR

7 Start-up

7.1 General Information

To ensure that start-up is performed correctly, it should only be

carried out by an after-sales service technician authorized by the

manufacturer. These measures can also include an additional

warranty under certain conditions (see Warranty). Start-up

should be carried out in heating operation.

7.2 Preparation

The following items need to be checked prior to start-up:

All of the heat pump connections must be established as de-

scribed in Chapter 6.

All valves that could impair the proper flow of the heating

water in the heating circuit must be open.

The air intake and air outlet paths must not be blocked in any

way.

The ventilator must turn in the direction indicated by the ar-

row.

The settings of the heat pump manager must be adapted to

the heating system in accordance with the controller’s oper-

ating instructions.

The condensate outflow must not be impaired.

7.3 Procedure

The heat pump is started up via the heat pump manager. Adjust-

ments should be made in compliance with the instructions.

If an overflow valve is fitted to maintain the minimum heat-

ing water flow rate, the valve must be adapted to the require-

ments of the heating system. Incorrect adjustment can lead to

faulty operation and increased energy consumption. We recom-

mend carrying out the following procedure to correctly adjust the

overflow valve:

Close all of the heating circuits that may also be closed during

operation (depending on the type of heat pump usage) so that

the most unfavorable operating state - with respect to the water

flow rate - is achieved. This normally means the heating circuits

of the rooms on the south and west sides of the building. At least

one heating circuit must remain open (e.g. bathroom).

The overflow valve should be opened far enough to produce the

maximum temperature spread between the heating flow and re-

turn flow listed in the following table for the current heat source

temperature. The temperature spread should be measured as

close as possible to the heat pump. The heating element of mono

energy systems should be disconnected during start up.

At hot water temperatures under 7 °C, start-up is not possible.

The water in the buffer tank must be heated to a minimum

of 18 °C with the second heat generator.

To ensure a problem-free start-up, the following procedure is to

be implemented:

1) Close all consumer circuits.

2) Ensure that the heat pump has the correct water flow.

3) Use the manager to select the automatic operating mode.

4) In the special functions menu, start the "Start-up" program.

5) Wait until a return temperature of at least 25 °C has been

reached.

6) Now slowly reopen the heating circuit valves in succession

so that the heating water flow is constantly raised by slightly

opening the respective heating circuit. The heating water

temperature in the buffer tank must not be allowed to drop

below 20 °C during this process. This ensures that the heat

pump can be defrosted at any time.

7) When all heat circuits are fully open and a return tempera-

ture of at least 18 °C is maintained, the heat pump start-up

is complete.

ATTENTION!

Operating the heat pump at low system temperatures may cause the heat

pump to break down completely.

Heat source

temperature

Max. temperature spread

between heating flow and return

flow

From To

-20 °C -15 °C 4 K

-14 °C -10 °C 5 K

-9 °C -5 °C 6 K

-4 °C 0 °C 7 K

1 °C 5 °C 8 K

6 °C 10 °C 9 K

11 °C 15 °C 10 K

16 °C 20 °C 11 K

21 °C 25 °C 12 K

26 °C 30 °C 13 K

31 °C 35 °C 14 K

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex LA 11MSR in the language / languages: English, German, French as an attachment in your email.

The manual is 1.88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex LA 11MSR

Dimplex LA 11MSR User Manual - Dutch - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex LA 11MSR Manual

Product: