Manual Dimplex HPL 6S-TUW2 (page 19 of 52) (English, German, French)

798227

Zoom out

Zoom in

1/52

www.glendimplex.de 452163.66.69 · FD 0010 EN-3

HPL 6S-TUW2 English

1.4 Energy-efficient use of the heat

pump

By operating this heat pump, you are helping to protect the en-

vironment. A prerequisite for energy-efficient operation is the

correct design of the heat source system and heating system.

It is particularly important for the efficiency of a heat pump to

keep the temperature difference between heating water and

heat source as small as possible. For this reason, it is advisable

to design the heat source and heating system very carefully. A

temperaturedifference of approximately one Kelvin (1 °C) in-

creases the power consumption by around 2.5 %. When de-

signing the heating system, it should be borne in mind that spe-

cial consumers such as domestic hot water preparation should

also be taken into consideration and dimensioned for low tem-

peratures. Underfloor heating systems (panel heating) are

optimally suited for heat pump use on account of the low flow

temperatures (30 °C to 40 °C).

It is important to ensure that the heat exchangers are not con-

taminated during operation, as this increases the temperature

difference, which in turn reduces the COP.

When set correctly, the heat pump manager is also an essential

factor in the energy-efficient use of the heat pump. Further in-

formation can be found in the heat pump manager operating

instructions.

2 Intended use of the heat

pump

2.1 Area of application

The air-to-water heat pump is intended exclusively for heating

or, depending on the device, also cooling heating water. It can

be used in new or existing heating systems.

The heat pump is suitable for mono energy and bivalent opera-

tion.

During continuous operation, proper defrosting of the evapora-

tor must be guaranteed by maintaining a heating water return

temperature of more than 18 °C.

The heat pump is not designed for the increased heat con-

sumption required when a building is being dried out. For this

reason, the additional heat consumption should be met using

special devices provided by the customer. For drying out a

building in autumn or winter, it is advisable to install a second

heat generator (e.g. an electric heating element available as an

accessory).

NOTE

The device is not suitable for operation with a frequency

converter.

2.2 Operating principle

Heating

Surrounding air is drawn in by the fan and fed through the evap-

orator (heat exchanger). The evaporator cools the air, i.e. ex-

tracts heat from it. This extracted heat is then transferred to the

working medium (refrigerant) in the evaporator.

The heat is brought to a higher temperature level by increasing

its pressure with the aid of an electrically driven compressor. It

is then transferred to the heating water via the liquefier (heat

exchanger).

Electrical energy is used to raise the temperature of the heat

from the environment to a higher level. Because the energy ex-

tracted from the air is transferred to the heating water, this type

of device is referred to as an air-to-water heat pump.

The main components of an air-to-water heat pump are the

evaporator, fan and expansion valve, as well as the low-noise

compressor, liquefier and the electrical control system.

At low ambient temperatures, humidity accumulates on the

evaporator in the form of frost, reducing the transfer of heat.

Uneven accumulation during this process does not indicate a

fault. The evaporator is defrosted automatically by the heat

pump as required. Under certain atmospheric conditions,

steam may be emitted from the air outlet.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex HPL 6S-TUW2 in the language / languages: English, German, French as an attachment in your email.

The manual is 2.2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex HPL 6S-TUW2 Manual

Product: