798062
13
Zoom out
Zoom in
Previous page
1/24
Next page
5.9 - Installer menu
It may be necessary to adjust certain temperature settings to
optimise the performance of the heat pump water heater,
depending on how the appliance is installed.
Accessing the installer menu:
• Press
Turn the dial until the screen displays
«installer menu.»
• Press the «Clock settings» and
«Menu» buttons simultaneously
Keep both buttons pressed down for 3 sec. until the
screen displays «pv mode»
To adjust the installation settings
settings
To activate photovoltaic operation
MODE PV
To go back to default settings
reset par.
To display temperatures of sensors
and inlets
display
To set the meters running, count
start-ups, etc.
counters
5.9.1 - PV mode
1. If the PV mode regulator is connected to connectors
1 and 2 on the electronics board, PV mode must be
activated.
The electrical energy which is produced is stored in
the form of hot water. The PV function can be set to
two dierent levels of production.
PV ECO = the lower level of the photovoltaic energy
production. The heat pump generates a higher
water temperature. The hot water temperature
must be somewhere between the regular hot water
temperature and 60°C (factory setting = 60°C).
PV MAX = the higher level of photovoltaic electricity
production. The heat pump and electrical back-up generate a
higher water temperature. The hot water temperature must be
somewhere between the eco mode hot water temperature and
65°C (factory setting = 65°C).
2. Turn the dial to set the mode:
- Menu INST. MENU PV mode.
3. Select « Yes »
4. Press the dial to conrm.
5. Press Menu.
6. Set the domestic hot water temperature.
7. Turn the dial to select the primary function:
- Menu INST. MENU MODE PV PRIORITY
• Yes: the signals from connectors 1 and 2 take precedence over
eco and frost protection modes.
• No: The eco and frost protection modes take precedence over
the signals from connectors 1 and 2.
N.B.: If PV mode is chosen as the primary function, the domestic
hot water will also be heated during non-selected time periods, e.g.
in holiday mode and outside of the programmed time slots.
If you only wish the domestic hot water to be heated during
authorised time slots, adjust the settings to No.
8. Press the dial to conrm your choice.
• For products which are equipped with an extra thermal heat
exchanger, no boiler request is sent when the heat pump is switched
on. Only the electrical back-up is on, to use the energy produced by
the PV function.
•When fan mode is activated, option 3 may no longer be chosen.
•The load shedding function is not available.
5.9.2 - Adjusting the operating settings
Select setting Modify the
setting
+
settings
Enter
• Press to return to the main menu.
5.9.2.1 - ANTI-BACT -anti-legionellosis cycle
Example :
anti-bact = 8,
temp. water = 60 C
the anti-legionellosis cycle
will run every 8 days at 10pm
Select number of days
ANTI-BACT
no
ANTI-BACT
8 d
Factory setting anti bact = NO
Factory setting temp. water = 60 C
TEMP. water
60 C
Select the temperature
Conrm
Conrm
• If the set temperature for domestic hot water is already 60°C
(see § «Setting the desired water temperature»), there will be no
anti-legionellosis cycle as it is already running continuously.
• Press to return to the main menu.
Parameter Description Unit Time
range Factory
setting
mode pv Activation of
photovoltaic mode yes
no
no
priority Interval of anti-
legionellosis cycles yes
no
yes
Parameter Description Unit Time
range Factory
setting
anti-
bact
Time interval
for anti-
legionellosis
cycle
days 0-99 0
fan
mode
Ventilation
mode 1,2,3 1
toC mini Min. temp for
electrical back-
up
0 or 1 0
shedding Load shedding
level 0,1,2 1
max.
time
Max. heating
time hours No,
auto, 1
to 24
No
- INSTALLER HEAT PUMP WATER HEATER 200 -270L AIR D/2 - MANUAL - 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Edel 270 AIR D-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Edel 270 AIR D-2 in the language / languages: English as an attachment in your email.

The manual is 2.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dimplex Edel 270 AIR D-2

Dimplex Edel 270 AIR D-2 User Manual - Dutch - 48 pages

Dimplex Edel 270 AIR D-2 Installation Guide - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info