648075

Dimplex DX 425 Manual

7
Zoom out
Zoom in
Previous page
1/24
Next page
www.dimplex.de/en DX410_430_gb · 04/15/B EN-7
English
DX 410, DX 415, DX 420, DX 425, DX 430
ATTENTION!
In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this appliance
must not be supplied through an external
switching device, such as a timer or
connected to a circuit that is regularly
switched on and off by the utility.
ATTENTION!
Connection only to fixed installed cables! The
hardwired electrical installation must be
provided with a disconnect device with a
contact grap of at least 3 mm at each pole
(e.g. automatic circuit breaker)!
2 Technical data
Connection voltage: 1/N/PE~, 230 V, 50 Hz
Protection type: IP20
Protection class: I (with protective conductor)
3 Mounting, Installation, Minimum Clearances
The heating device may only be installed as shown, i.e.
on a horizontal, even surface. Using it on deep-pile car-
pets is not permitted. Please use caution when install-
ing it in front of flammable objects. Installation below a
wall socket is not permissible. Minimum clearances
must be observed.
In addition, a minimum clearance of 500 mm between
flammable objects e.g. curtains, towels or heat-sensi-
tive plastics and the front of the unit must be main-
tained.
The heating device must be aligned horizontally and in-
stalled on a vertical wall (see illustration).
Make sure that the inflow and outflow of air at the top
and bottom of the device are unimpeded
.
It is not permissible to install the device in protection
zones as defined in VDE 0100 part 701.
3.1 Wall mounting
ATTENTION!
The original wall mounting bracket supplied, located at
the back of the heater, must be used.
Remove the bracket from the back of
the device by pressing the springs on
each side.
Drill the fixing holes for the wall mount-
ing bracket.
Firmly secure bracket to the wall using suitable
screws.
Insert heater in wall bracket making use of the slots
on the back of the heater. Snap heater in place at
the top of the wall bracket.
4 Electrical Connection
The voltage specified on the type plate must match the
local mains voltage.
The device plug must always be accessible.
The heaters are fitted with a power supply cable with-
out plug. The supply cord must be connected to a con-
nection box dedicated to the heater.
Type Heat out-
put (W)
Width
(mm)
Height
(mm)
Depth
(mm)
Weight
(kg)
DX 410 1000 575 350 124 4,1
DX 415 1500 575 350 124 4,1
DX 420 2000 575 350 124 4,1
DX 425 2500 695 350 124 4,8
DX 430 3000 695 350 124 4,8
Type Heat output (W) A (mm)
DX 410 1000 354
DX 415 1500 354
DX 420 2000 354
DX 425 2500 476
DX 430 3000 476
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex DX 425 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex DX 425 in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info