798034

Dimplex Cadiz Eco CDE2ECC Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
be noticed, this is quite normal – the fumes are non-toxic
and will quickly disappear. We recommend that you open a
window to ventilate the room when using the heater during
this time.
Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to
the element. This is normal and should not be a cause for
concern.
ELECTRICAL
WARNING: THIS APPLIANCE MUST BE EARTHED
The use of an extension lead or multi-plug adaptor is
not advised when connecting this product to the mains.
Connection through these devices could lead to a risk of
overloading, overheating and even re at the extension lead
or adaptor due to inadequate connection quality.
If the socket outlets in your home are not of the 13 amp
BS1363 type they will not accept the plug connected to this
heater, therefore cut off the plug. When cut off this plug can
constitute a shock hazard if inserted into a socket outlet. It
must therefore be disposed of safely.
Before wiring the appropriate plug please note that the
wires in this mains lead are coloured in accordance with
the following code:
GREEN/YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
Connect the Green/Yellow wire to the terminal marked E
or the earth symbol or coloured Green or Green/Yellow.
Connect the Brown wire to the terminal marked L or coloured
Red. Connect the Blue wire to the terminal marked N or
coloured Black.
DO NOT connect the Brown (Live) or the Blue (Neutral)
wires to the Earth terminal of your 13 amp plug. If the
terminals of the plug are unmarked or you are in any doubt,
consult a qualied electrician.
CAUTION: If you use this heater in conjunction with a
thermal control, programme controller, timer or any other
device which switches the heater on automatically observe
all safety warnings at all times.
Positioning the Heater
Select the position for the heater ensuring there is clearance
from any furniture and ttings of at least 300mm above the
heater and 150mm each side. The appliance should only
be operated on a at stable surface.
Operation
Important: Objects or clothing must not be placed on this
heater. Before using the heater ensure that all warnings
and instructions have been read carefully.
To bring the heater into use plug it in. Neon indicating lights
located at the controls area will glow when the appliance
is actually heating.
CONTROLS
Thermostat
(CDE2T, CDE2TI & CDE3TIE models only)
The Thermostat (see ‘T’ in Fig.’s 2 & 3) controls the heat
output according to the room temperature. This ensures
that the heater will not produce heat unnecessarily when
the room is warm. To set the temperature you require, turn
the thermostat knob clockwise until the required setting
is reached. Alternatively to heat a cold room quickly, turn
the thermostat knob up fully. When the room has reached
the desired temperature, turn the thermostat knob anti-
clockwise until the thermostat just clicks off. The heater
will now automatically operate at this temperature. The
thermostat also has a frost protection setting marked ‘ ‘.
This setting is useful in areas such as garages, to prevent
frost damage. If the thermostat is set to its minimum
setting ‘ ’, the heater will cycle on and off to maintain a
temperature of approximately 5° to help protect against frost.
Note – Should the heater fail to come on when the
thermostat is at a low setting, this may be due to the room
temperature being higher than the thermostat setting.
On/Off button (CDE2T &CDE2Ti Models Only)
This button controls the electricity supply to the elements.
When the On/Off button is activated a neon light ‘Y’
illuminates above the control button.
To turn off press the button ‘O’ located directly above the
On/Off button.
Mono and Dual Panel Heat Selection
Switches
(CDE2T, CDE2TI & CDE3TIE models only)
Selector switches located on the control panel provide
a choice of Half Heat or Full Heat output to suit varying
conditions and for economy of operation as follows:
Half Heat Setting - left hand side - This switch as
shown in Fig.’s 2 & 3 provides half heat output when
activated. When it is activated a neon light ‘x’ illuminates
above the control button and the left hand side element
turns on.
Half Heat Setting - right hand side - This switch as
shown in Fig.’s 2 & 3 provides a half heat output when
activated. When it is activated a neon light ‘x’ illuminates
above the control button and the right hand side element
turns on.
Centre ECO Element (CDE3Tie Only)- This model has an
additional central element which provides a boost of heat
to either the left hand or right hand element operation if
they do not provide enough heat output on their own. The
neon ‘Y’ above the button illuminates when it is activated.
This feature can also be used on its own as an ECO mode
when both heat panels are switched off to provide a low
level background heat.
Maximum Heat Setting
CDE2T &CDE2Ti Models - Maximum output is achieved
with both left and right hand side switches on and all neons
illuminated (see Fig.’s 2 & 3). Note that these models wil
only operate with the On/Off button in the On position and
all neons illuminated.
CDE3Tie Model - To achieve maximum heat output on this
model Left, Right and ECO elements must all be switched
on with all neons illuminated.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Cadiz Eco CDE2ECC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Cadiz Eco CDE2ECC in the language / languages: English as an attachment in your email.

The manual is 1.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info