Manual Dik Geurts Vision 100 (page 27 of 64) (English, German, Dutch, French)

695367

Zoom out

Zoom in

1/64

English

USER MANUAL

6. Maintenance

Dik Geurts fires are made of steel plate. A lot of attention is given to a sound manufacture and careful finish, as a

result of which your fire requires little maintenance. The following maintenance tips/instructions contribute to a

proper operation of your fire and therefore your comfort of use.

!CAUTION

• perform maintenance after the fire has been out of operation for at least 24 hours;

• do not make any changes to the fire yourself;

• as a user you are only allowed to perform the maintenance stated in this chapter, for any other work you will

have to consult an installer who has experience in the field of wood fire heating;

• only replace parts by original parts. These are available via your supplier/installer.

!Tip

Slightly open the fire door when you are not burning. This will prevent condensation and possible corrosion.

6.1 Cleaning

You can clean your fire whenever you want.

Clean the outside of the fire with a soft duster.

!Caution

• do not use corrosive or abrasive cleaning agents when cleaning your fire and/or glass pane, in order to prevent

damage;

• do not use water when cleaning, as the heat-resistant paint is not water repellent. Water may cause rust spots;

• do not put glasses, cups, etc. on the fire. Rings may cause rust spots.

Remove any deposits on the glass pane using the supplied glass pane cleaning agent. For this, observe the user

manual on the packaging (see section 6.6).

!Tip

The glass pane cleaning agent is available via your supplier/installer.

6.2 Paint

!Caution

Damages to the paint, resulting from objects that have fallen/been placed against the casing of the fire, are not

covered by the warranty.

!Caution

Paint is not anti-corrosive; be careful with moisture in and around the fire. The formation of rust or discolouration is

not covered by the warranty.

Small damages to the paint you can repair yourself, using the supplied spray can. It will be available via your

supplier/installer.

If, nevertheless, a rust spot appears on your fire, you can remedy this as follows:

Carefully sand the rust spot with steel wool.

Then treat this area with the supplied paint. Prior to this, you should check whether the colour indicated on the

spray can corresponds with the fire. In case of doubts, please contact your dealer.

Make sure the direct vicinity of the fire is covered, because of possible excess spraying.

!Tip

In case of damage to the paint, retouch an entire area and not only the damaged spot. This prevents

discolourations and spots.

6.3 Baffle plates

At the top of the fireplace you will find the so-called flame baffle plates (see Appendix 2, Fig. 9). These plates

increase the temperature in the fire and therefore the efficiency.

The flame baffle plates are easily replaced. In case of some fires, the bottom and side wall lining must be removed

first. For assembly and disassembly, please see the appliance specific section in the installation manual.

!CAUTION

• in case of collisions, the plate might break. When chimney sweeping, check the baffle plates for crack(s);

• when chimney sweeping, remove the baffle plates. Mark them so they can be returned at the same location.

• when placing them back, check whether the baffle plates still fit properly in their intended profiles;

• in case of excess condensation in the chimney, the flame baffle plate can become saturated with moisture and

therefore easily break. Consult your dealer/installer for a solution, if this problem occurs.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Vision 100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dik Geurts Vision 100 Manual

Product: