Manual Dik Geurts Prostyle 800V (page 41 of 112) (English, German, Dutch, French)

695348

Zoom out

Zoom in

1/112

English

INSTALLATION MANUAL

When replacing the cord proceed as follows:

Open the door.

Remove the cord and the mastic from the recess.

Apply a new layer of heat resistant mastic in the recess where the cord was.

Place a new cord in the recess. Do this loosely and do not pull the cord tight.

Insert both ends of the cord in the special sleeve.

The cord, the sleeve and the mastic are available through your supplier.

!Caution

Make sure that the sleeve is placed on the underside of the glass pane.

The door can also be adjusted in height. There are 2 eyelets on the upper pin on which the door is hung.

Removing 1 or more of these eyelets allows the door to fall to the desired level.

Proceed as follows when adjusting the door handle:

Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 8a

(Instyle and Prostyle 700) and 8b (Instyle and Prostyle 700). This pin ensures that the door is tightly clamped.

Adjust the pin.

Tighten the 2 hexagonal nuts again.

Test the sealing of the door (see the start of this paragraph).

Repeat this process if the result is not satisfactory.

9.4 Glass pane(s)

!Caution

• Avoid damage when removing/fitting the glass pane(s);

• Avoid/remove fingerprints on the glass pane(s) because these burn in.

Tip!

Use the supplied pane window cleaner to remove fingerprints/dirt on the glass pane(s).

9.4.1 Disassembly of glass pane in door(s)

To remove the glass pane in the door(s) follow the instructions below:

(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle applianc: see Appendix 2, fig. 10).

!Caution

When you install an Instyle or Prostyle Tunnel: Follow the instructions below. Then repeat these instructions on

the other side of the appliance.

Open the door.

Lift the door out by first sliding it upwards, then tilt it slightly forwards and allow it to lower.

Place the door on a flat surface.

Remove the nuts from the strips.

Remove the strips.

Lift the glass pane out. The pane seal is then also taken out.

Tip!

• When replacing the glass pane always replace the seal in the door (= seal between the glass pane and the

door).

• Check the door sealing cord and replace if necessary (see paragraph 9.3).

9.4.2 Assembly of glass pane in door(s)

Assemble the glass panes in the door(s) according to the steps described in paragraph 9.4.1 ‘Disassembly of glass

pane in door(s)’ but in reverse order.

(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle appliance: see Appendix 2, fig. 10).

!Caution

Assembly of the door(s) is somewhat different.

Proceed as for assembly of the door(s):

Bring the hole at the bottom of the hinging part of the door exactly below the lower pin.

Slide the door up. The pin slides into the lower hole.

Bring the hole at the top of the hinging part of the door exactly above the upper pin and allow the door to lower.

The pin slides into the upper hole.

The door is now assembled.

!Caution

• Do not fasten the bolts too tight to avoid breaking off and/or stripping: overtightening will cause breakage.

• Place the glass pane (including new pane seal) with the logo to the bottom right.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Prostyle 800V in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Prostyle 800V

Dik Geurts Prostyle 800V User Manual - English, German, Dutch, French - 64 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dik Geurts Prostyle 800V Manual

Product: