695348

Dik Geurts Prostyle 800V Manual

37
Zoom out
Zoom in
Previous page
1/112
Next page
English
INSTALLATION MANUAL
Ø
Use single-walled stainless steel flue pipes or stainless steel double-walled flexible pipes that at least meet the
requirements of standard EN 1856-2 T600.
Ø
The fire may never support the flue.
Ø
After the fire has been connected turn the adjustable legs with the Allen key supplied until the fire is in the
desired position. Make sure that the combustion air supply is not blocked when doing this.
Ø
Replace the restrictor cap for the outflow, fit the inner lining plates in reverse order and place the baffle plate
against the back wall and on the profiles (see section 9 'Appliance-specific information').
Ø
Use a torch or a thin screwdriver to check that the secondary ventilation holes in the back wall are directly facing
the recesses in the interior lining.
Ø
Replace the door and if applicable the frame around the fire (if applicable see section 9 'Appliance-specific
information').
Ø
Lay a fire-resistant floor plate for the fire if the floor is combustible. The floor plate of non-combustible material
must extend at least 300 mm away from the fire and be at least 300 mm wider than the fire.
5.7.3 Built-in fires
Ø
Determine the place of the fire.
Ø
Slide the build-in frame into the desired position.
Ø
Use non-combustible and heat-resistant material according to European fire classification A1 EN 13501-1 for the
plate on the floor, chimney breast (including the upper face), the material in the chimney breast and the back wall
against which the appliance is fitted. Plate material or stony materials can be used for this.
Ø
If there is a combustible ceiling, place a fire-resistant plate with a 10 cm thick heat-insulating layer on top 30 cm
below the ceiling in the chimney breast.
Ø
Place the fire level at the desired height and fix it with metal anchors.
Ø
Connect the flue duct to the fire ring.
Ø
Always connect any convection openings (see section 5.3 'Convection') with heat-resistant flexible pipe and
ventilation elements (see section 5.4 'Appliances wit fan(s)) to protect the plasterwork against high temperatures.
If the chimney breast is made of non-combustible materials (e.g. facing brickwork) this is not required.
Ø
Make sure there is sufficient space under the fire for the supply of combustion air. When the outside air
connection ring is not used, it must remain at least 20 mm free for sufficient combustion air.
Ø
If applicable connect the outside air connection (see section 9 'Appliance-specific information').
Ø
The fire is not suitable to support a flue duct, it must be self-supporting.
Ø
Stony materials may absolutely not rest on the fire. For this use e.g. a brick lintel with ceramic felt.
Ø
Make sure that the opening in the chimney breast is 6 mm wider than the built-in frame.
Ø
The chimney breast may not be warmer than 90 degrees Celsius on the outside.
Ø
Lay a fire-resistant floor plate for the fire if the floor is combustible. The floor plate in non-combustible material
must extend at least 300 mm away from the fire and be at least 300 mm wider than the fire.
5.8 Completing installation
Ø
Check if grit, dust or other materials are left behind in the chimney breast (odours).
Ø
Use clean fabric gloves and avoid fingerprints on the fire and flue pipes.
Ø
Check whether the interior lining and the baffle plates are fitted properly in the fire (if applicable see section 9
'Appliance-specific information'). Correct the position of these plates if necessary.
Ø
Check whether the holes of the secondary ventilation in the back plate are immediately facing the recesses in the
interior lining.
Ø
Clean the fire with a soft cloth and check it for damage. The fire can be sprayed with the spray can supplied.
Before doing this read the instructions for use on the label. Always first check the colour on a piece of white paper
or cardboard before you treat the fire.
First carefully read the user manual before starting to use the fire. We refer to the user manual for lighting and
burning the fire.
37
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Prostyle 800V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Prostyle 800V in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Prostyle 800V

Dik Geurts Prostyle 800V User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info