695350

Dik Geurts Prostyle 1000V Manual

43
Zoom out
Zoom in
Previous page
1/112
Next page
English
INSTALLATION MANUAL
9.7.1.2 Air slide valve
With installation and maintenance of the appliance check the operation of the air slide valve (see Appendix 2,
Fig. 18). There is the possibility that steel grit entered the air slide valve during transport. If the air slide valve does
not move smoothly it must be cleaned. The air slide valve must be disassembled to do this. The air slide valve is
suspended sprung by means of a bolt and a spring located below the cover plate.
Proceed as follows when disassembling the air slide valve (see Appendix 2, Fig. 18):
Ø
Remove the vermiculite plates and the felt from the bottom (see section 9.7.1.3.1).
Ø
Remove the 5 cover plate socket screws from the bottom.
Ø
Remove the cover plate.
Ø
If there is an outside air connection remove the 2 screws from the front strip.
!Caution
You only have to remove the front strip if an exterior connection is assembled.
Ø
Remove the socket screw with spring.
Ø
Remove the air slide valve by bringing it towards you.
Ø
Check the air slide valve and clean it if necessary.
To replace the air slide valve proceed as described for removal in reverse order.
9.7.1.3 Interior lining
9.7.1.3.1 Vermiculite
The fire’s vermiculite plates are located on the bottom against the rear wall and/or side walls of the appliance. In
the following situations the vermiculite plates must be taken out:
• When disassembling the air slide valve (see section 9.7.1.2).
• To be able to reach the adjustable legs (see section 9.6).
• When replacing the vermiculite plates.
The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the
vermiculite plates takes place in reverse order.
!Caution
Make sure that the vermiculite plates are replaced in the original position! The back plate with the small, not
countersunk, holes must be placed to the front.
9.7.1.3.2 Flame baffle plate
On delivery the flame baffle plate (see appendix 2, fig. 19) is located in the top section of the appliance. The flame
baffle plate must be removed in a number of situations:
• when mounting and checking the flue gas exhaust connection;
• when performing maintenance at the flue duct;
• when replacing the flame baffle plate.
For removing the flame baffle plate, proceed as follows:
Ø
Lift the left side of the flame baffle plate until it gets above the edge and slide the flame baffle plate to the right.
Ø
Lower the left side of the flame baffle plate and slide the flame baffle plate to the left.
Ø
Slide the right-hand side of the flame baffle plate over the edge.
Ø
Slide the flame baffle plate to the left and lower it until it reaches the lower section of the appliance.
Ø
Now you can remove the flame baffle plate.
Placing the flame baffle plate takes place in reverse order.
!Caution
The stainless steel profile must be placed at the front with the screw heads on top (see appendix 2, fig. 19).
43
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Prostyle 1000V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Prostyle 1000V in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Prostyle 1000V

Dik Geurts Prostyle 1000V User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info