Manual Dik Geurts Lars 900 (page 28 of 64) (English, German, Dutch, French)

695358

Zoom out

Zoom in

1/64

English

USER MANUAL

Do not burn the fire with no flame baffle plate.

If necessary, replace a broken or poorly fitting plate. It can be ordered via your supplier. Keep the old plate for the

dimensions.

!CAUTION

The risk of a chimney fire is greater if you burn your fire without a flame baffle plate.

6.4 Doorseal fire

The door is sealed with a ceramic strip or a springy stainless steel profile. In case of air leakage, more soot deposits

are created on the glass pane. If you establish leakage and your fire is sealed with a ceramic strip, please consult

your dealer or expert. In case of a sealing with springy stainless steel, see the description below.

!Caution

Check the door sealing at least once a year for leakage.

In case of a door with a springy stainless steel profile, space can be created between the profile and the door in due

time. You can easily solve this problem yourself.

Repair takes place as follows:

Open the door.

Put the palm of your hand against the edge of the door and press your fingertips against the bottom side of the

profile (see Appendix 2, Fig. 11).

Press your fingertips towards the palm of your hand in order to make the profile bulge again.

Adjust the profile in such a way that the door properly seals again.

!Tip

For the maintenance of the other seals, please refer to the installation manual provided.

6.5 Inner lining

At the bottom and on the side walls of the fire, heat-resistant plates are placed. These plates reflect the heat, have

an insulating effect and protect the steel plate walls of the fire. If cracks are created, for instance due to extreme

heat in the fire, this is not a problem. If lining plates are falling away from each other, they should be replaced.

For assembly and disassembly, please see the appliance specific installation manual.

!Caution

Check the lining plates at least once per year for crack(s).

!Tip

Keep the old plate/plates as a reference for the dimensions of the new plate/plates.

Remove the broken plate/plates, keep an eye on their order.

Place the new plate/plates in reverse order.

!Tip

• Mark the heat-resistant plates so that they can be replaced correctly (in the same location and orientation).

• Always heat the appliance to capacity using suitable, dry wood. Always leave a minimum layer of ash on the

floor of the appliance. This lengthens the service life of the appliance's inner lining.

!Caution

To guarantee the operation of the fire, check whether the holes in the heat-resistant plates correspond.

6.6 Glass pane

The fire has glass panes made of heat-resistant ceramic material.

!Caution

Very small irregularities in the glass panes cannot be avoided and are within the specified quality standards.

The glass pane is attached to the door by means of profiles or lips. After the fire has been burning a few times, a

little bit of play may occur at a glass pane. Tighten the nuts or press the clips tight when you notice the glass pane

getting a little bit of play. Do not overtighten the nuts, as overtightening will cause breakage.

When a glass pane is torn or broken, you must have it replaced.

Although the fire has a pane aeration system, there may still be deposits on the pane. Regularly remove any

deposits on the glass pane, using the glass pane cleaning agent supplied, as these deposits may burn into the glass

and will be difficult to remove.

!Caution

• Regularly check the glass pane for cracks/tears.

• Do not use corrosive and/or abrasive cleaning agents to clean the glass pane.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Lars 900 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dik Geurts Lars 900 Manual

Product: