810220
27
Zoom out
Zoom in
Previous page
1/64
Next page
26
English
USER MANUAL
6.1 Cleaning
You can clean your fire whenever you want.
Ø
Clean the outside of the fire with a soft duster.
!Caution
do not use corrosive or abrasive cleaning agents when cleaning your fire and/or glass pane, in order to prevent
damage;
do not use water when cleaning, as the heat-resistant paint is not water repellent. Water may cause rust spots;
do not put glasses, cups, etc. on the fire. Rings may cause rust spots.
Ø
Remove any deposits on the glass pane using the supplied glass pane cleaning agent. For this, observe the user
manual on the packaging (see section 6.6).
!Tip
The glass pane cleaning agent is available via your supplier/installer.
6.2 Paint
!Caution
Damages to the paint, resulting from objects that have fallen/been placed against the casing of the fire, are not
covered by the warranty.
!Caution
Paint is not anti-corrosive; be careful with moisture in and around the fire. The formation of rust or discolouration is
not covered by the warranty.
Small damages to the paint you can repair yourself, using the supplied spray can. It will be available via your
supplier/installer.
If, nevertheless, a rust spot appears on your fire, you can remedy this as follows:
Ø
Carefully sand the rust spot with steel wool.
Ø
Then treat this area with the supplied paint. Prior to this, you should check whether the colour indicated on the
spray can corresponds with the fire. In case of doubts, please contact your dealer.
Ø
Make sure the direct vicinity of the fire is covered, because of possible excess spraying.
!Tip
In case of damage to the paint, retouch an entire area and not only the damaged spot. This prevents
discolourations and spots.
6.3 Baffle plates
At the top of the fireplace you will find the so-called flame baffle plates (see Appendix 2, Fig. 9). These plates
increase the temperature in the fire and therefore the efficiency.
The flame baffle plates are easily replaced. In case of some fires, the bottom and side wall lining must be removed
first. For assembly and disassembly, please see the appliance specific section in the installation manual.
!CAUTION
in case of collisions, the plate might break. When chimney sweeping, check the baffle plates for crack(s);
when chimney sweeping, remove the baffle plates. Mark them so they can be returned at the same location.
when placing them back, check whether the baffle plates still fit properly in their intended profiles;
in case of excess condensation in the chimney, the flame baffle plate can become saturated with moisture and
therefore easily break. Consult your dealer/installer for a solution, if this problem occurs.
Ø
Do not burn the fire with no flame baffle plate.
Ø
If necessary, replace a broken or poorly fitting plate. It can be ordered via your supplier. Keep the old plate for the
dimensions.
!CAUTION
The risk of a chimney fire is greater if you burn your fire without a flame baffle plate.
UK
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dik Geurts Ivar 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dik Geurts Ivar 10 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 12.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dik Geurts Ivar 10

Dik Geurts Ivar 10 Installation Guide - English, German, Dutch, French - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info