499284

Digitalbox IMPERIAL DB 2 Manual

47
Zoom out
Zoom in
Previous page
1/48
Next page
DigitalBox Europe GmbH
Sandstraße 65 · D-40878 Ratingen
BDA Imperial DB 2_GB_TO.indd 48BDA Imperial DB 2_GB_TO.indd 48 15.10.2008 13:47:05 Uhr15.10.2008 13:47:05 Uhr
47 DVB-S Receiver
GB
7. TECHNICAL SPECIFICATION
VIDEO
Decoding . . . . . . . . . . . . . . . . . . . . . . . .MPEG-2 & MEPG-1 compatible
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . .Max 15Mbps
Output . . . . . . . . . . . . . . . . . . . . . . . . . .PAL/NTSC
Aspect ratio. . . . . . . . . . . . . . . . . . . . . .4:3, 16:9, Auto
Active pixel . . . . . . . . . . . . . . . . . . . . . . .720x480 @ 30fps; 720x576 @ 25fps
Output connector . . . . . . . . . . . . . . . . .RCA, TV SCART
AUDIO
Decoding . . . . . . . . . . . . . . . . . . . . . . . .MPEG-2/MPEG-1 layer I & II
Mode . . . . . . . . . . . . . . . . . . . . . . . . . .Mono, Dual, Stereo, Joint stereo
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . .Max 384Kbps
DEMODULATOR
Demodulation . . . . . . . . . . . . . . . . . . . .QPSK
Symbol rate . . . . . . . . . . . . . . . . . . . . . .SCPC/MCPC
Outer code. . . . . . . . . . . . . . . . . . . . . . .RS (204, 188, 8)
Inner code . . . . . . . . . . . . . . . . . . . . . . .ALL DVB rates
Energy dispersion. . . . . . . . . . . . . . . . .DVB-S recommendation
INPUT SIGNAL
Frequency. . . . . . . . . . . . . . . . . . . . . . . .950MHz
~
2150MHz
Input level . . . . . . . . . . . . . . . . . . . . . . . .-65dBm
~
-25dBm
Channel bandwidth. . . . . . . . . . . . . . . .36MHz
Input socked . . . . . . . . . . . . . . . . . . . . .F-type connector
LNB CONTROL
Power supply . . . . . . . . . . . . . . . . . . . . .13/18V (500mA max) with short circuit protection
Polarized control. . . . . . . . . . . . . . . . . .13/18V polarization (vertical/horizontal)
DiSEqC control . . . . . . . . . . . . . . . . . . .DiSEqC1.0, DiSEqC1.1 and DiSEqC1.2
RF MODULATOR
Input . . . . . . . . . . . . . . . . . . . . . . . . . .IEC 169-24 Male x 1
Output . . . . . . . . . . . . . . . . . . . . . . . . . .IEC 169-24 Female x 1
Band . . . . . . . . . . . . . . . . . . . . . . . . . .UHF
TV Standard . . . . . . . . . . . . . . . . . . . . .PAL BG/I/DK, NTSC M
Output Channel . . . . . . . . . . . . . . . . . . .21
~
69(PAL), 14
~
83(NTSC)
BDA Imperial DB 2_GB_TO.indd 47BDA Imperial DB 2_GB_TO.indd 47 15.10.2008 13:47:06 Uhr15.10.2008 13:47:06 Uhr
46Installation Guide
GB
6.5.2 Upgrade by Satellite
This function can upgrade the software of
your receiver through data sent by a satellite.
At the moment we offer satellite updates
only through ASTRA1 and Hotbird satellites.
1. Select the satellite and TP or input the TP
value and download PID.
2. Then mark “Start” and press [Enter] to
begin the download of the upgrade.
This may need up to 60 minutes. Therefore we suggest using of this function only if
you don’t intent to watch TV during this time.
6.6 SatcoDX Auto Programming
This function is using the tables of the SatcoDX websites to update your channel and
satellite lists. You need a special application which is available on the CD-ROM of the
Tele-Satellite magazine. Install this software on your PC fi rst.
1. Start the SatcoDX application on your PC.
2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK].
The screen will show the message “OK to Proceed”.
3. Press [OK] again and you will see the message “Ready to Download”.
4. In the PC application set the Baud Rate to 115200 and start the download procedure.
! Caution:
The new download channels will delete the original channels list. Please be careful
before using it.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 46BDA Imperial DB 2_GB_TO.indd 46 15.10.2008 13:47:06 Uhr15.10.2008 13:47:06 Uhr
45 DVB-S Receiver
GB
6.5 Software Upgrade
When you enter to “Software Upgrade”
menu, you will see a screen like beside:
1. Press [CH
] to select the wanted
item among Software Upgrade and
Upgrade by Satellite.
2. Press [OK] to enter the selected item.
6.5.1 Software Upgrade
1. This function allows you to upgrade the
software of the receiver. This can be done
from PC to receiver or from a master
receiver to a slave receiver.
2. Connect master receiver or PC to the
slave receiver via serial interface
(0-Modem cable). Enter the “Software
Upgrade” menu of the master receiver
and press [Vol ], to change the upgrade
mode. Upgrade modes include: All code/
Main code/CAS-data/Script GUI/Radio Back/default DB/Userdb.
3. Switch on the slave receiver.
4. Mark “Start” on the master reeciver and press [OK] to start upgrade.
Wait until the display on the front panel shows “-END”. Then switch off the receiver
and on again. Now the new software is used.
5. Press [MENU] to save the setting without upgrade.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 45BDA Imperial DB 2_GB_TO.indd 45 15.10.2008 13:47:07 Uhr15.10.2008 13:47:07 Uhr
44Installation Guide
GB
3. Othello
• Mark “Setup” and press [Vol
] to select
the game level (degree of diffi culty).
• Mark “Start” and press [OK] to start the
game.
• Mark “Cancel” and press [OK] to leave the
game.
• Play the game:
• Press [Vol /CH ] to position the
round mark.
• Press [OK] to set your stone.
• Press [Exit] to quit the game and return to the game menu.
6.4 Factory Default
When you press [OK] on the “Factory
Default” item:
1. A dialogue box will occur where you need
to enter the password.
2. After you input the correct password a
warning message will be displayed like the
one beside.
3. If you select “Yes” then all changes you
made will be reset to default values. Make sure you really want to do this!
4. Press [Exit] in both steps will close the window without resetting the receiver.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 44BDA Imperial DB 2_GB_TO.indd 44 15.10.2008 13:47:08 Uhr15.10.2008 13:47:08 Uhr
43 DVB-S Receiver
GB
Basic operation statement:
1. Tetris
• Mark “Setup” and press [Vol
] to
select the level (speed).
• Mark “Start” and press [OK] to start
the game.
• Mark “Cancel” and press [OK] to leave
the game.
• Play the game:
• Press [Vol ] to move the block left
or right
• Press [Channel ] to rotate the block clockwise
• Press [Channel ] to drop the block faster
• Press [OK] to Pause/Play the game
• Press [Exit] to leave the game and return to the game menu.
2. Snake
• Mark “Setup” and press [Vol ] to
select the level (speed).
• Mark “Start” and press [OK] to start
the game.
• Mark “Cancel” and press [OK] to leave
the game.
• Play the game:
• Press [Vol /CH ] to guide the
snake to the red blocks. Every block
you ate increases the length of the snake. If the snake runs against a wall or
against itself then it dies.
• Press [OK] to Pause/Play the game
• Press [Exit] to quit the game and return to the game menu.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 43BDA Imperial DB 2_GB_TO.indd 43 15.10.2008 13:47:09 Uhr15.10.2008 13:47:09 Uhr
42Installation Guide
GB
6. TOOLS
When you enter to “Tools” menu, you will see
a screen like beside:
In “Tools” menu:
1. Press [CH ] to select the wanted
item among Information, Quick Setup,
Game, Factory Default, Software Upgrade,
SatcoDX Auto Programming
2. Press [OK] to enter the selected item.
6.1 Information
1. When you select the “Information” menu
you will see a screen like beside. The
screen displays data about the current
channel.
2. Press [Exit] button to leave the informa-
tion display.
6.2 Quick Setup
When the STB is used, which need to repeat
set menu Language, First Audio, Second
Audio, LNB Power, Single Search and Multi
Search.
6.3 Game
When you enter “Game” menu, you will
see three games include Tetris, Snake and
Othello.
BDA Imperial DB 2_GB_TO.indd 42BDA Imperial DB 2_GB_TO.indd 42 15.10.2008 13:47:10 Uhr15.10.2008 13:47:10 Uhr
41 DVB-S Receiver
GB
5.6 Power setting
• Here you can set the power output to
the LNB. If your receiver is connected
to the LNB directly then you need to set
the LNB
Power to “On”. If your receiver is
connected
to a multi switch (SMATV signal
distribution system) then it may be that
you don’t need to provide the power to the
LNB. But since this is depending on the
kind of installed distribution system we
recommend you to contact your installer or to refer to the user manual of this system
to get the correct information.
• You also just can change this setting and check if you still can receive the channels.
If the LNB Power is off and you still can see all channels then we recommend this
setting in order to save energy.
5.7 RCU Position Switch
When many receivers are working at the
same time, In order to prevent the other
receivers to be disturbed when operating
the current receiver, here you can switch
RCU position, it has three items: Position 1,
Position 2 and Position 3, default position is
Position 1.
5. SYSTEM SETUP
BDA Imperial DB 2_GB_TO.indd 41BDA Imperial DB 2_GB_TO.indd 41 15.10.2008 13:47:11 Uhr15.10.2008 13:47:11 Uhr
40Installation Guide
GB
5. SYSTEM SETUP
5.5 Parental Lock
You can set a password for anyone who
wishes to operate the “Installation” menu.
You can also set the password to lock chan-
nels. Below you fi nd how to set and change
the password.
1. On “Parental Lock” press [OK] to open
a dialogue box and input the password.
After you entered the correct password,
you will see a screen like beside:
2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the password every
time you want to open the menu. If set to “No” then you can open the menu without
entering the password fi rst.
3. Channel Lock: If set to “Yes” then you need to enter the password before you can see
those channels which have been marked as locked channels in the channel menu. If
set to “No” then even those channels can be selected without entering the password
fi r s t .
4. New Password: Here you can change the existing password. You should do this
after you set up the receiver the fi rst time and every time when you think that your
password is known by unauthorized persons. To change the password enter the new
password in the “New Password” item and repeat the same one in the “Confi rm Pass-
word” item. If the passwords are not identically then you will see a warning message.
If you entered the same new password in both fi elds then you will see the message
“Saving Data, Please Wait…”. From now on you need to use the new password to
open locked menus or locked channels.
Note: The default password is 0000.
5. Press [Exit] to leave the “Parental Lock” menu.
BDA Imperial DB 2_GB_TO.indd 40BDA Imperial DB 2_GB_TO.indd 40 15.10.2008 13:47:12 Uhr15.10.2008 13:47:12 Uhr
39 DVB-S Receiver
GB
5. SYSTEM SETUP
5.4 OSD Setting
When you select “OSD Setting” you will see a
screen like beside:
1. Subtitle Display: Press [Vol
] to select
“Off”, “Standard” or “Teletext Subtitle”. If
the current channel has subtitle informa-
tion, it will be displayed if this function is
“Standard” or “Teletext Subtitle”. If this
function is “Off” subtitles won’t be dis-
played.
2. OSD Timeout: This setting determines the duration the info window is displayed on
the screen when you change channels. Press [Vol
], to set the time between 1 to
10 seconds.
3. Position: Press [Vol ] select the position between top and bottom.
4. OSD Transparency: With this parameter you can set the transparency of the menus.
Press [Vol ] select the value between 10%, 20%, 30%, 40% and “Off” (means no
transparency function).
5. Load OSD Setting Default: If you want to reset your OSD settings to the default
settings then select this item and press [OK].
6. Press [Exit] button to leave the “OSD Setting” menu.
BDA Imperial DB 2_GB_TO.indd 39BDA Imperial DB 2_GB_TO.indd 39 15.10.2008 13:47:12 Uhr15.10.2008 13:47:12 Uhr
38Installation Guide
GB
5. SYSTEM SETUP
2. Local Time Setting: When you select
“Local Time Setting” and press [OK] then
you will see a window like the one beside:
• GMT Usage: This item is used to set
the time by using the time signal from
the satellite. Press [Vol ] to change
the setting.
• The “GMT Offset” item is only available
when “GMT Usage” is set to “On”.
Press [Vol
] to set the “GMT Offset” value. With every time you press the button
the time offset will be increased/decreased by half an hour.
• Summer: Press [Vol ] to switch this function “On” or “Off”.
• “Date” and “Time” items are only available when the “GMT Usage” is set to “Off”.
Press [Vol ] to select one item and use number buttons to input time and date
directly.
• Time Display: Press [Vol ] to switch this function “On” or “Off”.
Note: If the current channel provides the correct time information, you will see the
current time after you entered “Local Time Setting” menu. If the channel doesn’t
provide time information, you have to input the date and time information manually.
The most channels support the time signal.
• Press [Exit] to leave the “Time” menu.
3. Sleep Timer: Select “Sleep Timer” item and press [OK] to set the sleep timer. You will
see “Sleep timer OFF/Sleep timer 10/Sleep timer 30/Sleep timer 60/
Sleep timer 90/Sleep timer 120”.
If you set a sleep time, the system will change to standby mode after the chosen time
period.
BDA Imperial DB 2_GB_TO.indd 38BDA Imperial DB 2_GB_TO.indd 38 15.10.2008 13:47:13 Uhr15.10.2008 13:47:13 Uhr
37 DVB-S Receiver
GB
5. SYSTEM SETUP
• When you select “Message” (reminding message) option in “Timer Service” then
you can enter additional data:
• Wakeup Message: Press [Vol
] to select the category
• of the wakeup message from Birthday, Anniversary and General.
• Wakeup Date: Use the [Number] buttons to input your wakeup date.
• On Time: Use the [Number] buttons to input your wakeup time. If date and time
are reached, no matter if the system is in standby mode or in playing mode, it
will automatically show a reminding message. The message will be displayed on
the screen until you press [Exit] to close it.
• Duration: Here you can set the time you want to see or play this channel. After
the time set the system will automatically switch to standby mode. If you don’t
want the box the be switched to standby mode then set the duration to 00:00.
• Press [Exit] to leave the “Timer” menu.
BDA Imperial DB 2_GB_TO.indd 37BDA Imperial DB 2_GB_TO.indd 37 15.10.2008 13:47:14 Uhr15.10.2008 13:47:14 Uhr
36Installation Guide
GB
5. SYSTEM SETUP
5.3 Time & Timer Setting
When you enter “Time & Timer Setting” a menu with this 3 items will be opened.
1. Timer: Select “Timer” item and press [OK]
to enter the “Timer” menu.
You can press [CH ] to select item.
• The current time will be displayed in
the fi rst column. If the current time
is incorrect, please modify it with the
[Number] buttons.
• Timer Number: You can press
[Vol
] to switch the timer number.
There are totally 8 timers.
• Timer Mode: Select how often the timer is running: Once, Daily, Weekly, Monthly
and Yearly, or switch the timer to off.
• Timer Service: Select between TV Channel, Radio Channel and Message.
• When you select “TV Channel/Radio
Channel” (timer setting for channel
change and Wakeup channel/date)
then you have further options you need
to set:
• Wakeup Channel: Press [OK] to
enter the channel list, and select the
channel you want to see with
[CH ], press [OK] to confi rm it.
• Wakeup Date: Use number buttons to input your wakeup date.
• On Time: Use number buttons to input your wakeup time. If date and time are
reached then no matter if the system is in standby mode or in playing mode, it
will automatically switch to the channel you set and start to play.
• Duration: Here you can set the time you want to see or play this channel. After
the time set the system will automatically switch to standby mode. If you don’t
want the box the be switched to standby mode then set the duration to 00:00.
BDA Imperial DB 2_GB_TO.indd 36BDA Imperial DB 2_GB_TO.indd 36 15.10.2008 13:47:14 Uhr15.10.2008 13:47:14 Uhr
35 DVB-S Receiver
GB
4. Subtitle Language: In “OSD Setting”menu, use [Vol ] to select “On” or “Off”. If the
current channel has subtitle information, it will be displayed if this function is “On”. If
this function is “Off” subtitles won’t be displayed. The selections of subtitle language
include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish,
Russian, Danish, Greek, Hungarian, Arabic and Farsi.
5. Teletext: Press [Text] button in TV mode to open the teletext page. This service is
depending on the support of the channel provider. If the channel does not support
teletext information, it will show “No Teletext Data” on the screen. The selections of
teletext language include: English, German, French, Spanish, Italian, Portuguese,
Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
6. Press [Menu/Exit] to return back from “Language” menu.
5.2 TV System
When you enter the “TV System” menu you
will see the screen like below:
1. Display Mode is used to switch the display
mode. You can select from Auto/PAL/
PAL-M/PAL-N/NTSC3.58/NTSC4.43.
Press [Vol ] to switch the desired mode.
2. Aspect Mode is used to switch the screen aspect ratio mode. You can select the
needed mode from Auto/4:3 PS/4:3 LB/16:9 with [Vol ].
3. Video output is use for switching the screen aspect ratio mode. Now we provide
below options: CVBS/CVBS + RGB/CVBS + S-Video. You can press [Vol ] key to
select each mode circularly.
5. SYSTEM SETUP
BDA Imperial DB 2_GB_TO.indd 35BDA Imperial DB 2_GB_TO.indd 35 15.10.2008 13:47:15 Uhr15.10.2008 13:47:15 Uhr
34Installation Guide
GB
5. SYSTEM SETUP
When you open the “System Setup” menu a
window like the one beside will be opened.
In “System Setup” menu:
1. Press [CH ] to select menu items
among Language, TV System, Time &
Timer setting, OSD Setting, Parental Lock
and Power setting.
2. Press [OK] to open the selected item.
5.1 Language
After selecting the “Language” menu you will
see a window like beside:
1. Menu Language: Press [Vol ] to select
languages. The selection of language
include: English, German, French, Spanish,
Italian, Portuguese, Turkish, Polish, Rus-
sian, Danish, Greek, Hungarian, Arabic
and Farsi.
2. First Audio: Some channels offer more than one audio language. This function
allows you to set the preferred audio language for those channels. If a channel offers
the same audio language as the “First Audio” you set the system will play this audio
language as default. If the channel does not offer this audio language then the system
will compare the offered languages with the second audio language. The selections of
audio language include: English, German, French, Spanish, Italian, Portuguese, Turkish,
Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
3. Second Audio: If the channel has no audio language that corresponds with “First
Audio” but with “Second Audio” the system will play the second audio language as
default. If no audio language corresponds with the “Second Audio” then the default
language of the current channel will be played instead. The selections of audio
language include: English, German, French, Spanish, Italian, Portuguese, Turkish,
Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
BDA Imperial DB 2_GB_TO.indd 34BDA Imperial DB 2_GB_TO.indd 34 15.10.2008 13:47:16 Uhr15.10.2008 13:47:16 Uhr
33 DVB-S Receiver
GB
4.6 Satellite Guide
When you enter “Satellite Guide” menu, you
will see the screen like beside:
Here you can enter your local longitude and
latitude and the satellite’s longitude. The
receiver calculates the antenna’s orientation
and elevation to point your antenna to the
selected satellite.
1. Use the [Number] buttons to input the
values of “Local Longitude”, “Local Latitude”
and “Satellite Longitude”.
2. In the “Calculate” item press [OK], the receiver auto calculates the antenna’s
orientation and elevation to point your antenna to the selected satellite.
3. Press [Menu/Exit] to return to the previous menu.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 33BDA Imperial DB 2_GB_TO.indd 33 15.10.2008 13:47:17 Uhr15.10.2008 13:47:17 Uhr
32Installation Guide
GB
4.5 TP List
When you open the “TP List” menu you will
see a window like the one beside.
1. Press [Vol
] to change the marked
satellite.
2. Press [Red] button to open the “Edit TP”
menu. Here you can edit the transponder’s
data.
3. Press [Green] button to open the “Add
TP” menu. Here you can add a new TP and
setup its parameters.
4. Press [Yellow] button will open a dialog
box asking you to confi rm the deletion of
the current TP. If you select “OK” all the re-
lated channels will be deleted. If you select
“Cancel” the operation will be cancelled.
5. Pressing the [Blue] button will open a dia-
log box asking you to confi rm the deletion
of all TP on current satellite. If you select
“OK”, all TP of the current satellite will be
deleted. If you select “Cancel” the opera-
tion will be cancelled.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 32BDA Imperial DB 2_GB_TO.indd 32 15.10.2008 13:47:17 Uhr15.10.2008 13:47:17 Uhr
31 DVB-S Receiver
GB
4.4 Satellite List
When you enter the “Satellite List” menu you
can see a window like the one beside:
1. Press [Red] button to enter edit satellite
menu. You can edit the satellite’s name
and its longitude.
2. Press [Green] button to open the “Add
satellite” window.
3. After pressing [Yellow] button you will be
asked “Are you sure to delete?”. Select
“OK” to delete the marked satellite. Select
“Cancel” to cancel the operation.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 31BDA Imperial DB 2_GB_TO.indd 31 15.10.2008 13:47:19 Uhr15.10.2008 13:47:19 Uhr
30Installation Guide
GB
• LNB Type: Press [Vol ] to switch
among “Standard”, “User” and “Univer-
sal” mode.
For Example: If you use a Dual LNB,
then you should select “User” option
in “LNB Type” and set the correct fre-
quency in LNB type.
• 22K: Use [Vol
] to switch “ON” and
“Off”. The 22KHz signal is used in KU
universal LNBs to change between low band and high band.
! Notice:
After choosing LNB type “Universal” you cannot modify 22K.
• DiSEqC1.0: Use [Vol ] to switch the options or press [OK] to open the DiS-
EqC1.0 option list to select directly with [CH ], press [OK] to confi rm it.
• DiSEqC1.1: Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter
DiSEqC1.1 option to select directly with [CH ], press [OK] to confi rm it. The op-
tions of this item are: Disable/CCard1 M1 Port1/CCard1 M1 Port2/
CCard1 M1 Port3/CCard1 M1 Port4/CCard1 M2 Port1/CCard1 M2 Port2/
CCard1 M2 Port3/CCard1 M2 Port4/CCard1 M3 Port1/CCard1 M3 Port2/
CCard1 M3 Port3/CCard1 M3 Port4/CCard2 Port1/CCard2 Port2/
CCard2 Port3/CCard2 Port4/CCard2 Port5/CCard2 Port6/CCard2 Port7/
CCard2 Port8/CCard2 Port9/CCard2 Port10/CCard2 Port11/
CCard2 Port12/CCard2 Port13/CCard2 Port14/CCard2 Port15/
CCard2 Port16.
• Positioner: Press [Vol ] to select between “Off/DiSEqC1.2/USALS”.
! Notice:
When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1” items will be
disabled.
• Polarity: Press [Vol ] to switch between “Auto/H/V ”.
• Toneburst: Press [Vol ] to switch this function “On” or “Off”.
5. After you completed your modifi cation, on the “TP Scan” item, press [OK] twice to
start scanning.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 30BDA Imperial DB 2_GB_TO.indd 30 15.10.2008 13:47:20 Uhr15.10.2008 13:47:20 Uhr
29 DVB-S Receiver
GB
4. INSTALLATION
4.3 TP Scan
When you enter “TP Scan” menu a window
like the one beside will be displayed.
1. In the “Satellite” item press [Vol
] to
select the satellite which you want to scan
or press [OK] to open the “satellite list” to
select directly with [CH ], press [OK]
to confi rm it.
2. TP Index: Use [Vol ] to select the desired transponder or press [OK] to open the
TP list to select directly with [CH ], press [OK] again to display the TP number
where the channel can be found. Press [Red/Green/Yellow] key on the RCU for the
related functions.
•
When you press [Red] it will display “New TP” in “TP Index” item. You have to set the
parameters of “TP Frequency”, “Symbol Rate” for this new transponder. Therefore
use the number buttons of the RCU. The available range are “3000
~
13450MHz” and
“1000
~
45000KS/s”.
• When you press [Green] a safety question will be displayed for confi rmation to delete
the current transponder or not. If you select “OK”, the current transponder will be
deleted and the total number of transponders will be reduced.
• When you press [Yellow] a safety question will be displayed for confi rmation to delete
all transponders or not. If you select “OK”, the all transponders on current satellite will
be deleted.
3.
For existing transponders you also can use number buttons to modify the parameters
of “TP Frequency” and “Symbol Rate” or [Vol ] to change the value directly.
“Polarity” and “FTA only” are used for setting scans conditions. Press [Vol ] to
select a different mode.
• On “TP Scan” item, press [OK] will open another window where you can set “Scan
Mode”, “Program Type” and “NIT Search”. Press [Menu/Exit] to return to the
previous menu.
• Press [Red] button to add a new TP.
• Press [Green] button to delete the current TP.
• Press [Yellow] button to delete all transponders on current satellite
4. Antenna Setup: Press [OK] to enter LNB confi guration, you will see a window like beside:
BDA Imperial DB 2_GB_TO.indd 29BDA Imperial DB 2_GB_TO.indd 29 15.10.2008 13:47:21 Uhr15.10.2008 13:47:21 Uhr
28Installation Guide
GB
4. INSTALLATION
4.2 Multi Search
When you enter the “Multi Search” menu a
window like the one beside will open.
1. In the “Satellite” item press [Vol
] to
select the satellite which you want to scan
or press [OK] to open the “satellite list” to
select directly with [CH ], and press
[OK] to mark/unmark and [MENU] to
fi nish the selection. You can select several
satellites in this menu. The system will use DiSEqC1.0/1.1, DiSEqC1.2 and USALS
functions to search the marked satellites and scan channels.
2. On “FTA Only” item, pres [Vol ] to select scanning of all channels or just scanning of
free channels. If you select “Yes”, it will scan free channels only.
3. On “Scan Channel” item, press [Vol ] to select the scanning range from TV + radio
channels, only TV channels or only radio channels.
4. On “Scan Mode” item, you can select “Auto Scan”, “Preset Scan” or “NIT Search” to
blind scan preset transponders or network transponders of the selected satellite.
5. Select “Search” and press [OK] to start scanning. In the lower part of the window the
progress of scanning and the found channels are displayed.
6. Press [Menu/Exit] to cancel or fi nish the scanning and saving the found channels.
BDA Imperial DB 2_GB_TO.indd 28BDA Imperial DB 2_GB_TO.indd 28 15.10.2008 13:47:22 Uhr15.10.2008 13:47:22 Uhr
27 DVB-S Receiver
GB
• DiSEqC1.0: Use [Vol ] to switch the options or press [OK] to open the
DiSEqC1.0 option list to select directly with [CH
], press [OK] to confi rm it.
• DiSEqC1.1: Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter
DiSEqC1.1 option to select directly with [CH ], press [OK] to confi rm it.
The options of this item are: Disable/CCard1 M1 Port1/CCard1 M1 Port2/
CCard1 M1 Port3/CCard1 M1 Port4/CCard1 M2 Port1/CCard1 M2 Port2/
CCard1 M2 Port3/CCard1 M2 Port4/CCard1 M3 Port1/CCard1 M3 Port2/
CCard1 M3 Port3/CCard1 M3 Port4/CCard2 Port1/CCard2 Port2/
CCard2 Port3/CCard2 Port4/CCard2 Port5/CCard2 Port6/CCard2 Port7/
CCard2 Port8/CCard2 Port9/CCard2 Port10/CCard2 Port11/
CCard2 Port12/CCard2 Port13/CCard2 Port14/CCard2 Port15/CCard2
Port16.
• Positioner: Press [Vol ] to select between “Off/DiSEqC1.2/USALS”.
Notice: When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1”
items will be disabled.
• Polarity: Press [Vol ] to switch between “Auto/H/V ”.
• Toneburst: Press [Vol ] to switch this function “On” or “Off”.
3. DiSEqC1.0 4Port: Use [Vol ] to switch the options of DiSEqC1.0. Between Dis-
able/LNB1/LNB2/LNB3/LNB4.
4. TP Index: Us [Vol ] to select the desired transponder or press [OK] to open the
TP list to select directly with [CH ], press [OK] again to display the TP number
where the channel can be found.
5. FTA Only: Press [Vol ] to select to scan only free channels or even scrambled
channels. If you select “Yes” it will scan free channels only.
6. Scan Channel: Press [Vol ] to select to scan TV + radio channels, or just TV
channels or just radio channels.
7. Scan Mode: You can select “Auto Scan”, “Preset Scan” or “NIT Search” to blind scan
preset transponders or network transponders of the selected satellite.
8. Search: Press [OK] to start scanning. In the lower part of the window the progress
of scanning and the found channels are displayed.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 27BDA Imperial DB 2_GB_TO.indd 27 15.10.2008 13:47:22 Uhr15.10.2008 13:47:22 Uhr
2Installation Guide
GB
SAFETY PRECAUTION
CAUTION:
The lightning fl ash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to „dangerous voltage“ and
to prevent from a risk of
electric shock.
Warning:
To reduce the risk of
electric shock, don‘t
open the cabinet. Refer
servicing to qualifi ed
personnel only.
The exclamation point
within an equilateral
triangle is intended to alert
the user to important
operating and maintenance
(servicing).
WARNING: Do not use this STB where contact with or immersion in water is a
possibility. Do not use near fl ower vase, washbowls, kitchen sinks, laundry tubs,
swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the
danger of fi re.
WARNING: The unit should be connected to a power supply only of the type descry
bed in the operating instructions or as marked on the unit. If you are not sure of the
type of power supply(for example: 120 or 230V) to your home, consult your local
dealer or local power company.
WARNING: Do not open the cabinet or touch any parts in the inner mechanism.
Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this user manual carefully
and retain for further reference.
Note: Do not open the cabinet to avoid the unit direct exposure to radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and
remote control with a soft cloth lightly moistened with a mild detergent solution.
BDA Imperial DB 2_GB_TO.indd 2BDA Imperial DB 2_GB_TO.indd 2 15.10.2008 13:47:42 Uhr15.10.2008 13:47:42 Uhr
… 47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Digitalbox IMPERIAL DB 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Digitalbox IMPERIAL DB 2 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Digitalbox IMPERIAL DB 2

Digitalbox IMPERIAL DB 2 User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info