Manual Dexford PCS 2000 (page 2 of 4) (English, German, French, Italian)

585373

Zoom out

Zoom in

1/4

PCS 2000

Solar Powered Alarm Desktop Clock with Projection

Introduction

This solar powered desktop clock comes with calendar, day, and temperature

display. lt is solar powered with optional backup DC batteries

1 Projection

2 [ SNOOZE / LIGHT ] button

3 [ MODE ] button

4 [ ALM SET ] button

5 [ -/C/F ] button

6 [ ALM ON/OFF ] button

7 [ +/12/24 ] button

8 Battery compartment

9 AC/DC input jack (not available in this model)

10 Solar panel on top

Getting started

Toggle the "On/Off" switch under battery compartment (8) to turn the clock on

and off.

Optional batteries installation

1. Open battery compartment (8) on the back of the unit.

2. Install / replace with 2x "AAA" size batteries in the compartment. lt is rec-

ommended that only alkaline batteries are used.

3. Replace the battery compartment (8) on the back of the unit.

4. A short beep will be heard to confirm proper installation of batteries.

Batteries safety warnings

1. Please read all instructions carefully before use.

2. Install batteries correctly by matching the polarities (+/-).

3. Always replace a complete set of batteries.

4. Never mix used and new batteries.

5. Remove exhausted batteries immediately.

6. Remove batteries when not in use.

7. Do not recharge and do not dispose of batteries in fire as the batteries

may explode.

8. Ensure batteries are stored away from metal objects as contact may

cause a short circuit.

9. Avoid exposing batteries to temperature or humidity extremes or direct

sunlight.

10. Keep all batteries out of reach from children. They are a choking hazard.

11. Please retain packaging for future reference.

To set time

1. Hold down the [ MODE ] button (3) for approximately 3 seconds until the dis-

play is flashing.

2. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the hour setting.

Press [ MODE ] button (3) to confirm.

3. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the minute set-

ting. Press [ MODE ] button (3) to confirm.

4. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the second set-

ting. Press [ MODE ] button (3) to confirm.

5. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the year setting.

Press [ MODE ] button (3) to confirm.

6. “date/month“ is flashing. Press [ MODE ] button (3) to confirm.

7. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the month setting.

Press [ MODE ] button (3) to confirm.

8. Press [ +/12/24 ] button (4) or [ -/C/F/RCC ] button (5) to change the date set-

ting. Press [ MODE ] button (3) to confirm.

9. Press [ +/12/24 ] button (4) or [ -/C/F/RCC ] button (5) to change the lan-

guage setting. ENG for English; GER for German; SPA for Spanish; ITA for

Italian; FRA for French. Press [ MODE ] button (3) to confirm.

10. The display will no longer flash.

To set alarm time

1. Press [ ALM SET ] button (4) until the alarm time is shown on the bottom right

hand corner.

2. Press and hold [ ALM SET ] button (4) for approximately 3 seconds until the

alarm display is flashing.

3. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the minute set-

ting. Press [ ALM SET ] button (4).

4. Press [ +/12/24 ] button (7) or [ -/C/F ] button (5) to change the hour setting.

Press [ ALM SET ] button (4).

5. The display will no longer flash.

6. Press [ MODE ] button (3) to show the temperature.

To activate the alarm

1. Set desired alarm time as per instructions above.

2. Press [ ALM ON/OFF ] button (8) to active the preset alarm. will be

shown.

3. Press [ ALM ON/OFF ] button (8) once more to activate automatic snooze.

will be shown.

4. Press [ ALM ON/OFF ] button (8) again to activate both alarm and automatic

snooze. and will be shown.

5. The alarm will sound for 60 seconds when the preset alarm time is reached.

Hit any button on the back of the clock to deactivate the alarm. The clock will

automatically enter snooze mode if the alarm is not deactivated.

6. Hit the [ SNOOZE / LIGHT ] button (2) when the alarm is on to enter snooze

mode. The alarm will sound again in 5 minutes. Hit any button on the back of

the clock to deactivate the alarm.

AM / PM and 24-hour clock setting

Press [ +/12/24 ] button (7) to toggle between AM / PM and 24-hour clock setting

when the time is shown.

Setting the Thermometer

Touch [ -/C/F ] button (5) to toggle between Fahrenheit and Celsius.

Projecting the current time

1. This clock is equipped with night time projection. The time can be projected

onto a flat surface in a very dark room.

2. Press the [ SNOOZE / LIGHT ] button (2) to activate the time projection. The

current time will be projected for approximately 3 seconds.

3. Turn the bottom knob clockwise or counterclockwise to adjust focus.

Warnings

• Do not subject the unit to excessive force, shock, dust, temperature or

humidity.

• Do not immerse the unit in water.

• Batteries recharge at its optimal with bright indirect sunlight.

• Avoid exposing unit to direct sunlight.

• The battery in this product is not replaceable. Do not replace.

• The rechargeabie battery has a limited shelf life.

• Dispose the complete unit when battery is no longer charging or when the

unit is no longer displaying the temperature.

• Do not remove any screws.

• Do not dispose this unit in a fire. IT MAY EXPLODE.

• Keep unit away from small children. The unit or parts of the unit might be a

choking hazard.

• Never attempt to recharge the batteries in any other methods.

• Solar cells will charge built-in rechargeable batteries at a minimum average

of 3,000 lux.

Specification

1. Calendar range: year 2000 to year 2069

2. This clock is equipped with night time projection. The time can be project-

ed onto a flat surface in a very dark room.

3. Press [ SNOOZE / LIGHT ] (2) to activate the time projection. The current

time will be projected for approximately 3 seconds.

4. The projection is auto-focus. Flat projection surface should be a minimum

800 mm (2'-10") away. For maximum clarity, the projection surface should

be no longer than 1800 mm (6'-0") away from the clock. This is approxi-

mately the distance between the top of a bed side table and the height of

common height ceiling.

Disposal

You can help protect the environment! Please remember to

respect the local regulations: Hand in the non-working electrical

equipments to an appropriate waste disposal center.

Hotline

In the event of technical problems, you can contact our hotline service,

Tel. 0900 00 1675 within Switzerland (cost via Swisscom at time of going to

print: CHF 2.60/min).

Conformity

This equipment complies with the European EMV directive. To view the

complete Declaration of Conformity, please refer to the free download

available at our web site: www.dexford.com

www.dexford.com V 1.0 / 27.06.2011

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dexford PCS 2000 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dexford PCS 2000 Manual

Product: