549679
37
Zoom out
Zoom in
Previous page
1/156
Next page
ENGLISH
35
2. Install the vac rack reusing the carry handle
screws. Put them back in their original holes
and tighten.
3. Use the 2 screws (bb) provided by placing
them in the rear holes of the vac rack. Push
down and turn each screw to break through the
material and into the hidden screw boss below.
Tighten.
CAUTION: Do not exceed 9 kg (20 lb)
in each 14 liter storage unit, maximum
2 storage units per dust extractor. Do
not exceed 18 kg (40 lb) in a 28 liter
storage unit, 1 storage unit per dust
extractor. Exceeding the recommended
height and/or weight could result in an
unstable dust extractor would could
cause injury or damage.
NOTICE: Do not remove dust extractor
head from tank with T-stack storage
units attached. Doing so could result in
damage to the dust extractor filters.
SECURING THE POWER CORD TO THE HOSE (FIG. 1)
The power cord (b) can be secured to the suction
hose (g) using the D279058CL hose clip (available
from your local DEWALT supplier).
Consult your dealer for further information on the
appropriate accessories.
Troubleshooting
PROBLEM SOLUTION
Motor
does not
run
Check power cord, plugs and outlet.
Ensure the on/off /tool control switch
is in the ON position ( ).
Suction
capacity
decreases
Remove blockages in the suction
nozzle, suction tube, suction hose
or filters.
Replace the paper or fleece bag.
Check for proper installation of the
filters.
Clean or replace the filters.
Empty canister, refer to Empty
Canister under Operation.
PROBLEM SOLUTION
Vacuum
stops
running
Thermal overload has been tripped:
1. Turn the vacuum off and
disconnect vacuum cleaner from
power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an
appropriate outlet and turn on/
off/tool control switch to the ON
position ( ) to test. If vacuum will
not restart contact your seller or
check the location of your nearest
authorised DEWALT repair agent
in the DEWALT catalogue or
contact your DEWALT office at the
address indicated in this manual.
Dust
comes
out while
vacuuming
Check for proper installation of the
filters.
Ensure filters are not damaged;
replace if necessary.
Ensure filter seals are in place and are
secure.
Automatic
filter
cleaning
is not
working
Listen for the solenoid clicking to
ensure the filter cleaning mechanism
is working.
Power tool
does not
turn on.
Ensure the on/off/tool control switch is
in the ACTIVATION position .
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWV902MT T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWV902MT T 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info