549675
2
Zoom out
Zoom in
Previous page
1/6
Next page
TO REMOVE FLAT CHISEL (FIG. 8–11)
1. Pull adaptor (B, C, D) down as shown.
2. Remove flat chisel (U) from tool holder as instructed in the tool instruction manual.
2. Open latch (I) and slide dust extraction system (A) from tool holder.
3. Remove adaptor (B, C, D).
Attach Dust Extraction System To Dust Extractor Vacuum
(Fig. 1, 12, 13)
WARNING: Use only power tools recommended by DEWALT with this attachment. For more
information about D
EWALT power tools compatible with this attachment, please contact your
local dealer, call 1-800-4-D
EWALT (1-800-433-9258) or visit our website www.dewalt.com.
Push dust extractor vacuum hose nozzle (P) into connection point (H) until tight. For a more
secure connection use the AirLock connection system.
NOTE: Ensure hose connection is secure.
AIRLOCK CONNECTOR SYSTEM - DWV9000 (SOLD SEPARATELY)
AirLock allows for a fast and secure connection between the dust extraction system and the
dust extractor vacuum.
1. Ensure the collar (Q) on the AirLock connector (M) is in the unlock position. Align notches
(R) on collar and AirLock connector as shown for unlock and lock positions.
2. Push the AirLock connector (M) onto the connection point (H) of the dust extraction
system (A).
3. Rotate the collar (Q) to the locked position. NOTE: The ball bearings (N) inside collar will lock
into slot (O) and secure the connection.
The dust extraction system is now securely connected to the dust extractor vacuum.
OPERATION
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the chipping tool and the dust extractor vacuum. Such preventative
safety measures reduce the risk of starting the tool accidentally.
WARNING: For your own safety, read the instruction manual for both the chipping tool and
the dust extractor vacuum before using any accessory. Failure to heed these warnings may
result in personal injury and serious damage to the tool and the accessory. When servicing this
tool, use only identical replacement parts.
CAUTION: DO NOT carry or guide the tool by the dust extractor vacuum. Hold the tool as
instructed in the tool instruction manual.
• Ensure latch is securely closed.
Ensure rotary function is disabled and that the hammerdrill is set to chiselling/rotary stop
mode.
NOTE: The amount of dust retained by the dust extractor vacuum is dependent on its filter
system. Refer to the dust extractor vacuum instruction manual for more information.
1. Turn the dust extractor vacuum on as instructed in the dust extractor vacuum instruction
manual.
2. Switch on the hammerdrill as instructed in the tool instruction manual.
NOTE: The two larger dust shrouds have bellows (T, Fig. 14) to increase flexibility when
working in tight or confined spaces.
MAINTENANCE
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the chipping tool and the dust extractor vacuum. Such preventative
safety measures reduce the risk of starting the tool accidentally..
Your chipping dust extraction system has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory operation depends on proper tool care
and regular cleaning.
TROUBLESHOOTING
FAULT POSSIBLE CAUSE REMEDY
Excessive dust
emission
dust extractor vacuum is full empty the dust extractor vacuum
suction channel is blocked clean the suction channel
The chisel is extended more
than 4.9" (125 mm)
use a shorter chisel or a longer dust
shroud
Dust Extraction
System does not
attach to hammer
the dust extraction system is
not assembled correctly
Refer to Assembly section.
adaptor and tool holder are
oily or greasy
remove oil and grease with a clean cloth
the locking latch is damaged replace locking latch
wrong adaptor being used select the correct adaptor
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only D
EWALT recommended accessories should be used with this product.
If you need assistance, please contact DEWALT Industrial Tool Co., 701 East Joppa Road,
Baltimore, MD 21286, call 1-800-4-D
EWALT (1-800-433-9258) or visit our website www.
dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be
performed by a D
EWALT factory service center, a DEWALT authorized service center or other
qualified service personnel. Always use identical replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
EWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D
EWALT tools are covered by our:
1 YEAR FREE SERVICE
D
EWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
EWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D
EWALT (1-800-433-9258) for a free replacement.
FIG. 1
I
E
F
G
B
D
H
A
C
FIG. 2
G
F
E
J, U
E, F, G
K
FIG. 3
B, C, D
I
L
A
A
I
J
FIG. 6
FIG. 7
M
FIG. 4 FIG. 5
A
J, U
S
4.9" (125 mm)
1.2" (30 mm)
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWH052 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWH052 T 1 in the language / languages: English as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWH052 T 1

DeWalt DWH052 T 1 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info