Manual DeWalt DWE6423 (page 25 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

712392

Zoom out

Zoom in

1/100

ENGLISH

Lubrication

Your power tool requires no additional lubrication.

Cleaning

NOTE: After the tool is used in metal sanding

applications without dust bag, clean the tool using

low-pressure air.

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Optional Accessories

WARNING: Since accessories, other

than those offered by DEWALT, have

not been tested with this product, use

of such accessories with this tool could

be hazardous. To reduce the risk of

injury, only DEWALT, recommended

accessories should be used with this

product.

Consult your dealer for further information on the

appropriate accessories.

Protecting the Environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you ﬁnd one day that your DEWALT product

needs replacement, or if it is of no further use to

you, do not dispose of it with household waste.

Make this product available for separate collection.

Sanding

Start with the coarsest grit size.

As the tool produces small abrasion marks in all

directions, it is not necessary to sand with the grain.

Check your work at short intervals.

Always switch off the tool when work is finished and

before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing

set-ups or when making repairs.

Be sure the trigger switch is in the OFF

position. An accidental start-up can

cause injury.

Replacing the Sanding Pad and the

Speed Limiter Belt (Fig. 4)

Your sander is equipped with a replaceable belt (m)

which is located between the pad (f) and the sander

body (j). It is designed to control the pad speed

while the unit is off the work surface. The belt and

the sanding pad (f) are designed to be consumable

parts and will occasionally need to be replaced.

The sanding pad needs replacement when signs

of wear become evident. Replacement of the belt

is necessary when the pad speed increases very

dramatically when the unit is lifted from the work

surface. These parts are available at extra cost from

your local dealer or authorised D

EWALT service

centre.

1. Holding the platen firmly, remove the four

screws (o) from the bottom of the pad.

2. Remove the pad (f).

3. Replace worn or damaged belt (m) by wrapping

it around the shoulder screw (k) and bearing

retainer (l) as shown in Figure4.

4. Reinstall pad (replace with new pad if

necessary). Replace the four screws (o). Be

careful not to over-tighten screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE6423 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWE6423 Manual

Product: