Manual DeWalt DWE6005 (page 28 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546441

Zoom out

Zoom in

1/124

ENGLISH

Inserting the Motor into the Base

(ﬁ g. 1, 3)

1. Open the locking lever (p) on the base.

2. If the depth adjustment ring (c) is not on the

motor, thread the ring (c) onto the motor until

the ring is about halfway between the top and

bottom of the motor. Insert the motor into the

base by aligning the groove in the back of the

motor unit with the groove pins (e) on the base.

Slide the motor down until the depth adjustment

ring snaps into place.

3. Adjust the depth of cut by turning the depth

adjustment ring. Refer to Adjusting the Depth

of Cut.

4. Close the locking lever (p) when the desired

depth is achieved. For information on setting the

cutting depth, Refer to Adjusting the Depth

of Cut.

Locking Lever Adjustment (ﬁ g. 1)

Excessive force should not be used to clamp the

locking lever (p). Using excessive force may damage

the base.

When the locking lever is clamped, the motor should

not move in the base.

Adjustment is needed if the locking lever will not

clamp without excessive force or if the motor moves

in the base after clamping.

ADJUSTING THE LOCKING LEVER’S CLAMPING FORCE

1. Open the locking lever (p).

2. Using a 2 mm hex wrench turn locking lever

adjustment screw (q) in small increments.

Turning the screw clockwise tightens the lever,

while turning the screw counterclockwise

loosens the lever.

Motor Quick Release (ﬁ g. 2)

1. Open the locking lever (p) on the base.

2. Grasp the motor unit with one hand, depressing

both quick release tabs (o).

3. With the other hand, grasp the base and pull

motor from the base.

Inserting and Removing a Cutter Bit

(ﬁ g. 1, 5)

NOTE: Bits are not included but are available as an

accessory.

1. Separate the motor unit (b) from the base.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-s)afe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

3–core extension cable suitable for the power input

of this tool (see Technical Data).The minimum

conductor size is 1.5 mm

; the maximum length

is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the rocker switch is in the OFF position.

An accidental start-up can cause injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE6005 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWE6005 Manual

Product: