548697
14
Zoom out
Zoom in
Previous page
1/48
Next page
ENGLISH
12
Support panels or any oversized
workpiece to minimize the risk
of wheel pinching and kickback.
Large workpieces tend to sag under
their own weight. Supports must be
placed under the workpiece near the
line of cut and near the edge of the
workpiece on both sides of the wheel.
Always wear regular working gloves
while operating this tool.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition to cool the
accessory. Do not touch accessories
before they have cooled. The discs
become very hot during use.
Never work with the grinding cup
without a suitable protection guard in
place.
Do not use the power tool with a cut-
off stand.
Never use blotters together with
bonded abrasive products.
Be aware, the wheel continues to
rotate after the tools is switched off.
Do not use separate reducing
bushings or adapters to adapt large
hole abrasive wheels.
Proper Hand Position (fi g. 1)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the body of the
tool, as shown in figure 1.
Switching On and Off (fi g. 1)
The on/off switch is equipped with an unlocking
switch.
To run the tool, depress the unlocking switch (b) and
subsequently operate the on/off switch (a).
Release the unlocking switch (b).To stop the tool,
release the switch.
Lock-on Button
For continuous operation depress the lock-on button
(g) and release the on/off trigger switch.
To stop the tool press the on/off switch again.
The lock-on button can be permanently removed
without compromising compliance with regulatory
agencies shown on the tool’s nameplate. Removal
of the lock pin must be done by a D
EWALT Service
Center.
Spindle Lock (fi g. 1)
The spindle lock (c) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Metal Applications
When using the tool in metal applications, make
sure that a residual current device (RCD) has been
inserted to avoid residual risks caused by metal
swarf.
If the power supply is shut off by the RCD, take the
tool to authorised DEWALT repair agent.
WARNING: In extreme working
conditions, conductive dust can
accumulate inside the machine housing
when working with metal. This can result
in the protective insulation inthe machine
becoming degraded with a potential risk
of an electrical shock.
To avoid build-up of metal swarf inside the machine,
we recommend to clear the ventilation slots on a
daily basis. Refer to Maintenance.
Cutting Metal
When cutting, work with moderate feed, adapted to
the material being cut. Do not exert pressure onto
the cutting disc, tilt or oscillate the machine.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE4579 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4579 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 7,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWE4579 T 1

DeWalt DWE4579 T 1 User Manual - English, German, Dutch, Danish, French, Italian - 204 pages

DeWalt DWE4579 T 1 Additional guide - Polish - 24 pages

DeWalt DWE4579 T 1 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info