548697
12
Zoom out
Zoom in
Previous page
1/48
Next page
ENGLISH
10
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
EWALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
Attaching Side Handle (fi g. 6)
WARNING: Before using the tool,
check that the handle is tightened
securely.
For grinding, screw the side handle (e) tightly into
one of the holes (q) on either side of the gear case
(fig. 6).
For cutting, screw the side handle (e) tightly into the
top hole (r) or into one of the holes (q) on either side
of the gear case.
Fitting and Removing a
Backing pad/Sanding sheet (fi g. 4)
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (l).
3. Place the rubber backing pad correctly onto the
spindle (m).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (n) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (c) and rotate the
spindle (m) until it locks in position.
7. Tighten the threaded clamp nut (n) with the two-
pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (n) with the two-pin
spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
Mounting and Removing the Guard
(fi g. 2)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
CAUTION: Guards must be used with
this grinder.
When using the DWE4557, DWE4597, DWE4559,
DWE4579 or the DWE4599 grinder for cutting metal
or masonry a Type 1 guard MUST be used. Type
1 guards are available at extra cost from DEWALT
distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
show other accessories that can be used with these
grinders.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE4579 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4579 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 7,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWE4579 T 1

DeWalt DWE4579 T 1 User Manual - English, German, Dutch, Danish, French, Italian - 204 pages

DeWalt DWE4579 T 1 Additional guide - Polish - 24 pages

DeWalt DWE4579 T 1 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 204 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info