Manual DeWalt DWE4120 (page 46 of 208) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

712337

Zoom out

Zoom in

1/208

english

• Never work with the grinding cup

without a suitable protection guard

inplace.

• Do not use the power tool with a cut-

off stand.

• Never use blotters together with

bonded abrasive products.

• Be aware, the wheel continues to

rotate after the tools is switched off.

Proper Hand Position (ﬁg. 1, 6)

WARNING: To reduce the risk of serious

personal injury, ALWAYS use proper

hand position as shown.

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the side

handle(C), with the other hand on the body of the

tool, as shown in Figure 1.

Switches

CAUTION: Hold the side handle and

body of the tool firmly to maintain control

of the tool at start up and during use

and until the wheel or accessory stops

rotating. Make sure the wheel has come

to a complete stop be fore laying the tool

down.

NOTE: To reduce unexpected tool movement,

do not switch the tool on or off while under load

conditions. Allow the grinder to run up to full speed

before touching the work surface. Lift the tool from

the surface before turning the tool off. Allow the tool

to stop rotating before putting it down.

SLIDER SWITCH (FIG. 3)

(DWE4056, DWE4057, DWE4156, DWE4157)

WARNING: Before connecting the tool

to a power supply, be sure the slider

switch is in the off position by pressing

the rear part of the switch and releasing.

Ensure the slider switch is in the off

position as described above after any

interruption in power supply to the tool,

such as the activation of a ground fault

interrupter, throwing of a circuit breaker,

accidental unplugging, or power failure.

If the slider switch is locked on when the

power is connected, the tool will start

unexpectedly.

To start the tool, slide the ON/OFF slider switch(G)

toward the front of the tool. To stop the tool, release

the ON/OFF slider switch.

the rotating accessory and run the power tool

at maximum no-load speed for one minute.

Damaged accessories will normally break apart

during this test time.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

WARNING:

• Ensure all materials to be ground or cut

are secured in place.

• Secure and support the workpiece.

Use clamps or a vice to hold and

support the workpiece to a stable

platform. It is important to clamp and

support the workpiece securely to

prevent movement of the workpiece

and loss of control. Movement of the

workpiece or loss of control may create

a hazard and cause personal injury.

• Support panels or any oversized

workpiece to minimize the risk

of wheel pinching and kickback.

Large workpieces tend to sag under

their own weight. Supports must be

placed under the workpiece near the

line of cut and near the edge of the

workpiece on both sides of the wheel.

• Always wear regular working gloves

while operating this tool.

• The gear becomes very hot during use.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on

thedisc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition to cool the

accessory. Do not touch accessories

before they have cooled. The discs

become very hot during use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4120 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWE4120 Manual

Product: