548035
14
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH
12
Never work with the grinding cup
without a suitable protection guard in
place.
Do not use the power tool with a cut-
off stand.
Never use blotters together with
bonded abrasive products.
Be aware, the wheel continues to
rotate after the tools is switched off.
Proper Hand Position (fi g. 1, 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle(c), with the other hand on the body of the
tool, as shown in Figure 1.
Switches
CAUTION: Hold the side handle and
body of the tool firmly to maintain
control of the tool at start up and during
use and until the wheel or accessory
stops rotating. Make sure the wheel has
come to a complete stop be fore laying
the tool down.
NOTE: To reduce unexpected tool movement,
do not switch the tool on or off while under load
conditions. Allow the grinder to run up to full speed
before touching the work surface. Lift the tool from
the surface before turning the tool off. Allow the tool
to stop rotating before putting it down.
ON/OFF TOGGLE SWITCH (FIG. 3)
(DWE4001, DWE4110)
WARNING: Before using the tool,
check that the handle is tightened
securely.
To run the tool press the switch (h) in before moving
it completely forward.
To stop the tool move the switch (h) back the
opposite way.
To stop the tool in continuous operation, press on
the back part of the switch.
WARNING: Do not switch the tool on
or off when under load.
SLIDER SWITCH (FIG. 3)
(DWE4050, DWE4051, DWE4150, DWE4151)
WARNING: Before connecting the tool
to a power supply, be sure the slider
switch is in the off position by pressing
the rear part of the switch and releasing.
Ensure the slider switch is in the off
position as described above after any
interruption in power supply to the tool,
such as the activation of a ground fault
interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure.
If the slider switch is locked on when the
power is connected, the tool will start
unexpectedly.
To start the tool, slide the ON/OFF slider switch(g)
toward the front of the tool. To stop the tool, release
the ON/OFF slider switch.
For continuous operation, slide the switch toward
the front of the tool and press the forward part of
the switch inward. To stop the tool while operating
in continuous mode, press the rear part of the slider
switch and release.
PADDLE SWITCH (FIG. 3) (DWE4002, DWE4120)
1. To turn the tool on, push the lock-off lever(j)
toward the back of the tool, then depress the
paddle switch(i). The tool will run while the
switch is depressed.
2. Turn the tool off by releasing the paddle switch.
Spindle Lock (fi g. 1)
The spindle lock(a) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Metal Applications
When using the tool in metal applications, make
sure that a residual current device (RCD) has been
inserted to avoid residual risks caused by metal
swarf.
If the power supply is shut off by the RCD, take the
tool to an authorised DEWALT repair agent.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE4120 T 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4120 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DWE4120 T 1

DeWalt DWE4120 T 1 User Manual - English, German, Dutch, Danish, French, Italian - 228 pages

DeWalt DWE4120 T 1 Additional guide - Polish - 24 pages

DeWalt DWE4120 T 1 User Manual - Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 228 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info