Manual DeWalt DWE4110 T 1 (page 12 of 40) (English, French)

548032

Zoom out

Zoom in

1/40

ENGLISH

MOUNTING CLOSED (TYPE 1) GUARD

WARNING: If present, the One-Touch

guard screw, lever, and spring must be

removed before attempting to mount

the closed (Type 1) guard. The removed

parts must be retained and reinstalled

to use the One-Touch guard. Noting

the position of these parts before

disassembly will aid in reassembly.

1. Open the guard latch. Align the lugs(l) on the

guard with the slots (m) on the gear case.

2. Push the guard down until the guard lug

engages and rotates freely in the groove on the

gear case hub.

3. Rotate guard into desired working position.

The guard body should be positioned between

the spindle and the operator to provide

maximum operator protection.

4. Close the guard latch to secure the guard on

the gear case cover. You should be unable to

rotate the guard by hand when the latch is in

closed position. If rotation is possible, tighten

the adjusting screw with the clamp lever in the

closed position. Do not operate grinder with a

loose guard or clamp lever in open position.

5. To remove the guard, open the guard latch,

rotate the guard so that the arrows are aligned

and pull up on the guard.

NOTE: If, after a period of time the closed (Type 1)

guard becomes loose, tighten the adjusting screw

with the clamp lever in the closed position.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to authorized repair agent to repair or

replace the guard.

NOTICE: Do not tighten adjusting

screw with clamp lever in open position.

Undetectable damage to guard or

mounting hub may result.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 1, 4, 5)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange(d) correctly onto the

spindle(b) (fig. 4).

3. Place the disc(q) on the backing flange(d).

When fitting a disc with a raised centre, make

sure that the raised centre(p) is facing the

backing flange(d).

4. Screw the threaded clamp nut(e) onto the

spindle(b) (fig. 5):

a. The ring on the threaded clamp nut(e) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut(e) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button(a) and rotate the

spindle(b) until it locks in position.

6. Tighten the threaded clamp nut(e) with the hex

key provided or a two pin spanner.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut(e) with the hex key provided or a two pin

spanner.

NOTE: Edge grinding can be performed with

Type27 wheels designed and specified for this

purpose; 6 mm thick wheels are designed for

surface grinding while 3 mm wheels are designed for

edge grinding. Cutting can be performed by using a

Type 1 wheel and a Type 1 guard.

Mounting Wire Brushes

andWire Wheels

Wire cup brushes or wire wheels screw directly

on the grinder spindle without the use of flanges.

Use only wire brushes or wheels provided with a

M14threaded hub (DWE4001/DWE4002 M10). A

Type 27 guard is required when using wire brushes

and wheels.

CAUTION: Wear work gloves when

handling wire brushes and wheels.

They can become sharp.

CAUTION: Wheel or brush must not

touch guard when mounted or while

in use. Undetectable damage could

occur to the accessory, causing wires to

fragment from accessory wheel or cup.

1. Thread the wheel on the spindle by hand.

2. Depress spindle lock button and use a wrench

on the hub of the wire wheel or brush to tighten

the wheel.

3. To remove the wheel, reverse the above

procedure.

NOTICE: Failure to properly seat the

wheel hub before turning the tool on

may result in damage to tool or wheel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE4110 T 1 in the language / languages: English, French as an attachment in your email.

The manual is 5,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWE4110 T 1 Manual

Product: