546642

DeWalt DWE398 Manual

31
Zoom out
Zoom in
Previous page
1/132
Next page
ENGLISH
29
3. Switch the tool on before placing blade in
contact with the workpiece. Refer to Switching
On and Off instruction in this manual.
WARNING: Apply only a gentle
pressure to the tool and do not exert
side pressure on the saw blade.
4. After blades have engaged the workpiece,
guide the tool back and forth in a rotating, see
saw like motion as the blades cut down through
the workpiece. Refer to Figure 6.
5. Once cut is complete, release the trigger switch.
To increase performance and lifetime of non-painted
saw blades, regularly apply oil to the blades and in
the oil holes (j) (every 15–30 min.). Do not lubricate
painted blades.
Regularly check the saw blade setting screws (m).
Sawing in Cellular Concrete,
Low Density and Medium Density
Building Blocks (fi g. 5)
WARNING: Cellular concrete, low
density and medium density building
blocks contain lime and quartz sand.
After use to guarantee optimum
performance, the saw blades, the bar
and the saw blade guide slot (i) must be
thoroughly cleaned, using the cutting
slot scraper. (DWE399 only)
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
Lubrication
• Lubricate the saw blades (if fitted with
non-painted blades), the bar and the saw blade
guide slot upon cleaning. Do not lubricate
painted blades.
• If the tool will not be used for a long period of
time, coat the non-painted saw blades and fill
the oil holes with a little oil (e.g., machine oil) Do
not oil painted blades.
Let the tool run for a few seconds to enable the
oil to reach all parts. This protects the tool from
corrosion.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
the tool. These chemicals may weaken
the materials used in these parts. Use
a cloth dampened only with water and
mild soap. Never let any liquid get inside
the tool; never immerse any part of the
tool into a liquid.
Regularly remove the saw blades after cutting
cellular concrete or thermal building blocks.
Thoroughly clean the saw blades and the bar. To
clean the saw blade guide slot use the scraper
supplied with the tool. (DWE399 ONLY)
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DEWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWE398 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWE398 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info