Manual DeWalt DWD522KS (page 35 of 156) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544724

Zoom out

Zoom in

1/156

ENGLISH

After the side handle is rotated into position, it

should be pushed rearward until the slots (k) on

the lip of the side handle are aligned with and

fully engaged with the projecting tabs (m) on the

underside of the gear case. The side handle is then

securely clamped by turning clockwise until tight.

OPERATION

Instructions for Use

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING:

• Always observe the safety instructions

and applicable regulations.

• To reduce the risk of personal

injury, ALWAYS ensure workpiece

is anchored or clamped firmly.

If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

• To reduce the risk of personal

injury, always operate the tool

with the side handle properly

installed. Failure to do so may result

in the side handle slipping during tool

operation and subsequent loss of

control. Hold tool with both hands to

maximize control.

• Do not attempt to tighten or loosen

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to

the chuck and personal injury may

occur.

• Burn Hazard. ALWAYS wear gloves

when changing bits. Accessible metal

parts on the tool and bits may get

extremely hot during operation. Small

bits of broken material may damage

bare hands.

Proper Hand Position (ﬁ g. 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (e) with the other hand on the main handle

(g).

Keyless Chuck (ﬁ g. 7–9)

DWD522, DWD524, DWD525, DWD530

The DWD522, DWD524, DWD525 and DWD530

feature a keyless chuck (c) for greater convenience.

To insert a drill bit or other accessory, follow the

steps listed below.

1. Grasp the rear half of the chuck with one hand

and use your other hand to rotate the front half

counterclockwise, as shown in figure 7. Rotate

far enough so that the chuck opens sufficiently

to accept the desired accessory.

2. Insert the bit or other accessory about 3/4"

(19 mm) into the chuck and tighten securely

by holding the rear half of the chuck and

rotating the front portion in the clockwise

direction. When the chuck is nearly tightened,

you will hear a clicking sound. After 4–6 clicks,

the chuck is securely tightened around the

accessory.

3. To release the accessory, repeat step 1 listed

above.

WARNING: Do not attempt to tighten

drill bits (or any other accessory) by

gripping the front part of the chuck

and turning the tool on. Damage to the

chuck and personal injury may result.

KEYLESS CHUCK REMOVAL (FIG. 8)

Tighten the chuck around the shorter end of a hex

key (not supplied) of 1/4" (6 mm) or greater size.

Using a soft hammer or piece of wood, strike the

longer end in the counterclockwise direction. This

will loosen the chuck so that it can be unscrewed

by hand.

KEYLESS CHUCK INSTALLATION (FIG. 9)

Screw the chuck on by hand as far as it will go.

Tighten the chuck around the shorter end of a 1/4"

(6 mm) or larger hex key (not supplied). Strike the

longer end in the clockwise direction with a soft

hammer.

Keyed Chuck (ﬁ g. 1)

D21570

The D21570 features a keyed chuck (c). To insert

a drill bit or other accessory, follow the steps listed

below.

1. Tighten chuck collar by hand.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWD522KS in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,27 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DWD522KS Manual

Product: