500486

DeWalt DWD010 Manual

27
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH
25
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data).
The minimum conductor size is 1.5 mm
2
.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Forward/Reverse Lever (fi g. 1)
The forward/reverse lever (c) is used for withdrawing
bits from tight holes and removing screws. It is
located above the trigger switch.
To reverse the motor, release the trigger switch
FIRST and then push the lever to the right (viewed
when holding the drill in the operating position).
After any reversing operations, return lever to
forward position.
Keyed Chuck (fi g. 1, 2, 3)
DWD010, DWD014
The DWD010 and the DWD014 feature a keyed
chuck (d).
TO INSERT A DRILL BIT OR OTHER ACCESSORY
1. Open the chuck jaws by turning collar by hand
and insert the shank of the bit about 19 mm
(3/4") into chuck. Tighten the chuck collar by
hand.
2. Place chuck key in each of the three holes, and
tighten in clockwise direction. It’s important to
tighten chuck with all three holes.
To release the bit, turn the chuck counterclockwise
in just one hole, then loosen the chuck by hand.
REMOVAL OF KEYED CHUCK (FIG. 2)
Tighten the chuck around the shorter end of a hex
key. Using a soft hammer, strike the key sharply in
the counterclockwise direction when viewed from
the front of the tool. This will loosen the chuck so
that it can be removed by hand.
KEYED CHUCK INSTALLATION (FIG. 3)
Screw the chuck on by hand as far as it will go.
Insert the shorter end of a hex key and strike it in the
clockwise direction with a soft hammer.
Keyless Chuck (fi g. 1, 4–6)
DWD014S
The DWD014S features a keyless chuck (d) for
greater convenience.
TO INSERT A DRILL BIT OR OTHER ACCESSORY
1. Grasp the rear half of the chuck with one hand
and use your other hand to rotate the front half
counterclockwise, as shown in Figure 4. Rotate
far enough so that the chuck opens sufficiently
to accept the desired accessory.
2. Insert the bit or other accessory about 19 mm
(3/4") into the chuck and tighten securely by
holding the rear half of the chuck and rotating
the front portion in the clockwise direction.
When the chuck is nearly tightened, you
will hear a clicking sound. After 4–6 clicks,
the chuck is securely tightened around the
accessory.
3. To release the accessory, repeat step 1 listed
above.
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to the
chuck and personal injury may result.
KEYLESS CHUCK REMOVAL (FIG. 5)
Tighten the chuck around the shorter end of a hex
key (not supplied). Using a soft hammer or piece of
wood, strike the longer end in the counterclockwise
direction. This will loosen the chuck so that it can be
unscrewed by hand.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DWD010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DWD010 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info