Manual DeWalt DW998 T 5 (page 24 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

549641

Zoom out

Zoom in

1/100

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (8), insert it into the

charger (10) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (11) will blink.

After approx. 1 hour, it will stop blinking and

remain on. The battery pack is now fully charged.

The battery pack can be removed at any time or

left in the connected charger indefinitely.

Inserting and removing the battery pack

• Insert the battery pack into the pistol grip (7)

until it clicks in place.

• To remove the battery pack, press the two

release buttons (9) simultaneously and pull the

pack out of the pistol grip (7).

Inserting and removing bits (fig. A & B)

Your drill is equipped with a bit holder (6).

• Open the chuck by turning the sleeve (12)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode (fig. C)

This tool can be used in two operating modes:

Drilling:

for steel, wood and plastics.

Hammerdrilling:

simultaneous rotating and impacting for

concrete and masonry drilling operations.

• Select the required operating mode by aligning

the symbol on the mode selector (4) with the

arrow (13) on the housing.

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

en - 5 20

ENGLISH

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or .

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of your charger

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

Assembly and adjustment

• Prior to assembly and adjustment,

always remove the battery pack.

• Always switch off the tool before

inserting or removing the battery pack.

• Use only DEWALT battery packs and

chargers.

Battery pack (fig. A)

Charging the battery pack

When charging the battery pack for the first time, or

after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles,

the battery pack will attain full capacity. Always check

the mains prior to charging the battery pack. If the

mains is functioning but the battery pack does not

charge, take your charger to an authorised DEWALT

repair agent. Whilst charging, the charger and the

battery pack may become warm to touch. This is a

normal condition and does not indicate a problem.

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW998 T 5 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW998 T 5 Manual

Product: