Manual DeWalt DW996K2 (page 27 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

447167

Zoom out

Zoom in

1/96

ENGLISH

en - 5

Using an extension cable

An extension cord should not be used unless

absolutely necessary. Use an approved triple-core

extension cable suitable for the power input of your

charger (see technical data). The minimum conductor

size is 0.5 mm

; the maximum length is 30 m.

Assembly and adjustment

Prior to assembly and adjustment,

always remove the battery pack.

Always switch OFF the tool before

inserting or removing the battery pack.

Battery pack (fig. A)

Charging the battery pack

When charging the battery pack for the first time, or

after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles,

the battery pack will attain full capacity.

Always check the mains prior to charging the battery

pack. If the mains is functioning but the battery pack

does not charge, take your charger to an authorised

DEWALT repair agent. Whilst charging, the charger

and the battery pack may become warm to touch.

This is a normal condition and does not indicate a

problem.

Do not charge the battery pack at

ambient temperatures <4 °C or >40 °C.

Recommended charging temperature:

approx. 24 °C.

• To charge the battery pack (8), insert it into the

charger (10) as shown and plug in the charger.

Be sure that the battery pack is fully seated in the

charger. The red charging indicator (11) will blink.

After approx. 1 hour, it will stop blinking and

remain on. The battery pack is now fully charged.

The battery pack can be removed at any time or

left in the connected charger indefinitely.

Inserting and removing the battery pack

• Insert the battery pack into the pistol grip (7) until

it clicks in place.

• To remove the battery pack, press the two

release buttons (9) simultaneously and pull the

pack out of the pistol grip (7).

Inserting and removing a bit (fig. A & B)

This DEWALT Cordless Power Tool is equipped with

a bit compartment (6).

• Open the chuck by turning the sleeve (12)

counterclockwise and insert the bit shank.

• Tighten firmly by turning the sleeve clockwise

while holding the rear part of the chuck with one

hand.

• To remove the bit, proceed in reverse order.

DW976 & DW996 - Selecting the operating mode

(fig. C)

The percussion drills can be used in two operating

modes:

Drilling: for steel, wood and plastics.

Percussion drilling: simultaneous rotating

and impacting for concrete and masonry

drilling operations.

• Select the required operating mode by aligning

the symbol on the mode selector (4) with the

arrow (13) on the housing.

Forward/Reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always release the variable speed switch

and wait until the motor has come to a

complete standstill before changing the

direction of rotation.

Two gear selector (fig. C)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque (drilling large holes or

driving large screws)

2 high speed/low torque (smaller holes, drilling in

wood)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or completely back.

Do not change gears at full speed or

during use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW996K2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW996K2 Manual

Product: