Manual DeWalt DW976 (page 25 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

447175

Zoom out

Zoom in

1/100

Always release the variable speed switch

and wait until the motor has come to a

complete standstill before changing the

direction of rotation.

Two gear selector (fig. C)

Your tool is fitted with a two gear selector (3) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes or driving large screws)

2 high speed/low torque

(smaller holes, drilling in wood)

For speed rates, refer to the technical data.

Always push the two gear selector

completely forward or completely back.

Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. E & F)

• Open the chuck jaws as far as possible.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure E.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise.

• Tighten an Allen key (14) into the chuck and

strike it with a hammer as shown in figure F.

This will loosen the chuck so that it can be

unscrewed by hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

Prior to operation:

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Make sure your battery pack is (fully) charged.

• Select forward or reverse rotation.

Switching on and off (fig. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• To stop the tool, release the variable speed

switch (1).

• To lock the tool in OFF-position, move the

forward/reverse slider (2) to the central position.

Screwdriving (fig. C & D)

• Select forward or reverse rotation using the

slider (2).

• Use the low speed/high torque position

(1st gear) (3).

• Set the torque adjustment collar (4). The higher

the number on the collar, the higher the torque

and the larger the fastener which can be driven.

Hammerdrilling (fig. C)

• Select the hammer mode.

• Press the variable speed switch (1).

• To stop the tool, release the switch.

Drilling (fig. C)

• Select the drilling mode.

• Proceed as described for hammerdrilling.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

• Unplug the charger before cleaning the housing

with a soft cloth.

• Remove the battery pack before cleaning your

Power Tool.

ENGLISH

21 en - 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW976 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW976 Manual

Product: