549661
28
Zoom out
Zoom in
Previous page
1/96
Next page
21
Removing and fitting the chuck (fig. E & F)
Open the chuck jaws as far as possible.
Tighten an Allen key (14) into the chuck and
strike it with a hammer as shown in figure E.
Insert a screwdriver into the chuck and remove
the chuck retaining screw by turning clockwise.
Tighten an Allen key (14) into the chuck and
strike it with a hammer as shown in figure F.
This will loosen the chuck so that it can be
unscrewed by hand.
To refit the chuck, proceed in reverse order.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework
and wiring.
Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
Prior to operation:
Insert the appropriate bit.
Mark the spot where the hole is to be drilled.
Make sure your battery pack is (fully) charged.
Select forward or reverse rotation.
Switching ON and OFF (fig. A)
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the variable speed
switch (1).
To lock the tool in OFF-position, move the
forward/reverse slider (2) to the central position.
Screwdriving (fig. C & D)
Select forward or reverse rotation using the
slider (2).
Use the low speed/high torque position
(1st gear) (3).
Set the torque adjustment collar (4) (DW976 &
DW996). The higher the number on the collar,
the higher the torque and the larger the fastener
which can be driven.
DW976 & DW996 - Percussion Drilling (fig. C)
Select the percussion mode.
Press the variable speed switch (1).
To stop the tool, release the switch.
All models - Drilling (fig. C)
Select the drilling mode (DW976, DW996).
Proceed as described for percussion drilling.
Consult your dealer for further information on the
appropriate accessories.
Maintenance
Your DEWALT Power Tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication
Your Power Tool requires no additional lubrication.
Cleaning
Unplug the charger before cleaning the housing
with a soft cloth.
Remove the battery pack before cleaning your
Power Tool.
Keep the ventilation slots clear and regularly
clean the housing with a soft cloth.
Environment
Rechargeable battery pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
Run the battery pack down completely, then
remove it from the tool.
NiCd cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
ENGLISH
en - 6
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW961 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW961 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info