Manual DeWalt dw907k2 (page 39 of 172) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

386361

Zoom out

Zoom in

1/172

ENGLISH

INSERTING AND REMOVING BITS (FIG. 1, 4)

1. Open the chuck by turning the sleeve (p)

counterclockwise and insert the bit shank.

2. Place the bit in the chuck as far as it will go and

lift slightly before tightening.

3. Tighten firmly by turning the sleeve clockwise.

4. To remove the bit, proceed in reverse order.

SELECTING THE OPERATING MODE OR ADJUSTING THE

TORQUE (FIG. 5)

The collar of this tool has 15 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to Screwdriving.

Select the drilling mode or torque by aligning the

symbol or number on the collar (e) with the indicator

(q) on the housing.

FORWARD/REVERSE SLIDER (FIG. 6)

To select forward or reverse rotation, use the

forward/ reverse slider (b) as shown (see arrows on

tool).

WARNING: To reduce the risk of

personal injury, always wait until the

motor has come to a complete standstill

before changing the direction of rotation.

TWO-GEAR SELECTOR (FIG. 7)

Your tool is fitted with a two-gear selector (f) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

WARNING: To reduce the risk of

personal injury:

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and Fitting the Chuck

(ﬁ g. 8, 9)

DW907

1. Open the chuck jaws as far as possible.

2. Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure 8.

3. Tighten an hex key into the chuck and strike it

with a hammer as shown in figure 9. This will

loosen the chuck so that it can be unscrewed

by hand.

4. To refit the chuck, proceed in reverse order.

Prior to Operation

1. Make sure your battery pack is (fully) charged.

2. Insert the appropriate bit.

3. Mark the spot where the hole is to be drilled.

4. Select forward or reverse rotation.

OPERATION

Instructions for Use

WARNING: To reduce the risk of

personal injury:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool. Excessive force does not

speed up drilling but decreases tool

performance and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the

operation.

• Keep the motor running when pulling

the bit back out of a drilled hole. This

will help prevent jamming.

Proper Hand Position (ﬁ g. 1, 10)

WARNING: To reduce the risk of

serious personal injury, ALWAYS

use proper hand position as shown

in figure 10.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on top of

the housing, with the other hand on the grip (h).

SWITCHING ON AND OFF (FIG. 1, 6)

1. To run the tool, press the variable speed switch

(a). The pressure exerted on the variable speed

switch determines the tool speed.

2. To stop the tool, release the switch.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt dw907k2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt dw907k2 Manual

Product: