546925
29
Zoom out
Zoom in
Previous page
1/128
Next page
ENGLISH
27
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Mounting the Side Handle (fi g. 2)
Screw the side handle (e) tightly into one of the holes
on either side of the tool.
Fitting and Removing the Backing
Pad (fi g. 3)
1. Place the tool on a table, spindle up.
2. Press the spindle lock (d) and turn the spindle
until the lock engages.
3. Place the backing pad (f) onto the spindle.
4. Screw the threaded flange (g) onto the spindle.
5. Tighten the threaded flange.
6. Release the spindle lock.
7. To remove the backing pad, loosen the
threaded flange while the spindle lock is
engaged.
Fitting the Polishing Bonnet (fi g. 4)
1. Place the tool on a table, spindle up.
2. Pull the polishing bonnet (h) over the backing
pad (f).
Prior to Operation
1. Be sure the threaded flange is mounted
correctly.
2. Make sure the pad rotates in the direction of the
arrows on the accessory and the tool.
3. Make sure any dirt is washed off the workpiece
surface.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING:
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
backing pad.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Polishing (fi g. 1)
1. Always use clean polishing bonnets.
2. Evenly apply a required amount of polishing
paste over the polishing bonnet.
3. Hold the polishing bonnet to the surface to be
polished and switch on the tool.
4. Move the tool evenly over the surface, without
applying pressure.
5. Switch off the machine before taking the tool
from the surface.
6. Check your work at short intervals.
WARNING: High-speed rubbing
action of the polishing bonnet upon the
workpiece surface can build a static
charge on the metal portions of this
tool resulting in a static shock when
touched.
Proper Hand Position (fi g. 7)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the main
handle (i).
Switching On and Off (fi g. 5)
1. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
2. For continuous operation, also press the lock-
on button (b). The lock-on button works only in
full speed.
3. Switching off: press the on/off switch again.
WARNING: Do not switch the tool on
or off when under load.
Speed Control (fi g. 6)
The speed control dial (c) can be used for advance
setting of the required maximum tool speed.
1. Turn the speed control dial (c) to the desired
position. The higher the number, the higher the
maximum tool speed.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW849 T 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW849 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info