Manual DeWalt DW831 T 3 (page 30 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian)

548022

Zoom out

Zoom in

1/124

DW840 - Mounting (fig. B2 & C2)

• Place the angle grinder on a table, spindle up.

• Align the lugs (6) with the slots (7).

• Press the guard (8) down and turn it in the

direction of the arrow (fig. B2).

• Securely tighten the screws (9).

DW840 - Removing

• To remove the guard, proceed in reverse order.

MOUNTING AND REMOVING A GRINDING WHEEL OR

CUTTING DISK (FIG. D & E)

• Place the tool on a table, guard up.

• Fit the spacer (11) correctly onto the spindle (10).

• Place the grinding wheel or cutting disk on the

spacer.

• Screw the threaded flange (12) onto the

spindle (10).

• Press the spindle lock (5) and rotate the grinding

wheel or cutting disk until it locks in position.

• Tighten the threaded flange using the two-pin

spanner (13) supplied.

• Release the spindle lock.

• To remove the grinding wheel or cutting disk,

loosen the threaded flange using the two-pin

spanner (while the spindle lock is engaged).

MOUNTING THE SIDE HANDLE (FIG. F)

• Screw the side handle (3) tightly into one of the

holes (14) on either side of the gear case.

Instructions for use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the

tool. Do not exert side pressure on the

grinding wheel or cutting disk.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

• Check that mounted wheels are

correctly fitted according to the

instructions given in this manual.

• Ensure that blotters are used when they

are provided with the abrasive wheel

and when they are required.

• Do not use separate reducing bushings

or adapters to adapt large hole abrasive

wheels.

• Never use the tool without the guard in

place.

• Be aware, the wheel continues to rotate

after the tools is switched off.

Prior to operation:

• Install the appropriate guard and disk or wheel.

Do not use excessively worn disks or wheels.

• Be sure the spacer and threaded flange are

mounted correctly.

• Make sure the disk or wheel rotates in the

direction of the arrows on the accessory and the

tool.

• Do not use cutting-off wheels for side grinding.

• Ensure that sparks resulting from use do not

create hazard e.g. do not hit persons, or ignite

flammable substances.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure

that the tool is off.

SWITCHING ON AND OFF (FIG. G)

CAUTION: Hold the side handle and

body of the tool firmly to maintain control

of the tool at start up and during use

and until the wheel or accessory stops

rotating. Make sure the wheel has come

to a complete stop be fore laying the tool

down.

• To run the tool, press the lock-off button (2) and

the ON/OFF-switch (1). For continuous operation,

press the lock-on button (2) and release the

ON/OFF-switch.

• To stop the tool, release the ON/OFF-switch.

To stop the tool in continuous operation, press

the ON/OFF-switch once more.

WARNING: Do not switch the tool ON or

OFF when under load.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW831 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW831 T 3

DeWalt DW831 T 3 Additional guide - Polish - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW831 T 3 Manual

Product: