548013
11
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH
9
Mounting and Removing the Guard
(fi g. 3)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
TO MOUNT THE GUARD
1. Align the lugs (i) on the guard with the slots (j) in
the bracket located on the gear case (fig. 3a).
2. Press the guard down towards the gear case
and rotate the guard in the direction of the
arrow (fig. 3b).
3. The guard locking pin (k) prevents the guard
from loosening while allowing the guard to
rotate 105˚.
TO REMOVE THE GUARD
1. Place the tool upside down on a flat surface.
2. Hold the tool in your hand and rotate the guard
in the direction of the arrow with your thumb
(fig. 3c). At the same time, using a screwdriver
or other pointed instrument, press the locking
pin in the slot so that the lug on the guard
comes into view (fig. 3d).
3. The guard, no longer held by the locking pin,
can be pushed free by thumb pressure.
NOTE: Please refer to the Grinding Accessory
Chart at the end of this section to show other
accessories that can be used with these grinders.
Fitting and Removing a Grinding Disc
(fi g. 4, 5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the inner flange (l) correctly onto the spindle
(m) (fig. 4).
3. Place the disc (n) on the flange (l). When fitting
a disc with a raised center, make sure that the
raised centre (o) is facing the flange (l).
4. Screw the outer flange (q) onto the spindle (m)
(fig. 5). The ring on the flange (q) must face
towards the disc when fitting a grinding disc.
5. Press the spindle lock (b) and rotate the spindle
(m) until it locks in position.
6. Tighten the flange (q) with the two-pin spanner
supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the flange (q) with
the two-pin spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
Prior to Operation
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the inner and outer flange are mounted
correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
WARNING:
Ensure all materials to be ground are
secured in place.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Proper Hand Position (fi g. 1, 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW806 T 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW806 T 6 in the language / languages: English as an attachment in your email.

The manual is 3,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info