Manual DeWalt DW718XPS T 4 (page 31 of 136) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546175

Zoom out

Zoom in

1/136

ENGLISH

• Check periodically that the motor air slots are clean and free of chips.

• Replace the kerf plate when worn. Refer to service parts list included.

• Disconnect the machine from the mains before carrying out any

maintenance work or when changing the blade.

• Never perform any cleaning or maintenance work when the machine is

still running and the head is not in the rest position.

• When possible, always mount the machine to a bench,

• If you use an LED to indicate the cutting line, make sure that the LED is

of class 2 according to EN 60825-1. Do not replace an LED diode with

a different type. If damaged, have the LED repaired by an authorised

repair agent.

• The front section of the guard is louvered for visibility while cutting.

Although the louvers dramatically reduce flying debris, they are

openings in the guard and safety glasses should be worn at all times

when viewing through the louvers.

• Connect the saw to a dust collection device when sawing wood.

Always consider factors which influence exposure of dust such as:

-– type of material to be machined (chip board produces more dust

than wood);

-– sharpness of the saw blade;

-– correct adjustment of the saw blade,

-– dust extractor with air velocity not less than 20m/s.

Ensure that the local extraction as well as hoods, baffles and chutes are

properly adjusted.

• Please be aware of the following factors influencing exposure

to noise:

-– use saw blades designed to reduce the emitted noise;

-– use only well sharpened saw blades;

• Machine maintenance shall be conducted periodically;

• Provide adequate general or localized lighting;

• Ensure that any spacers and spindle rings are suitable for the purpose

as stated in this manual.

• Refrain from removing any cut-offs or other parts of the workpiece from

the cutting area while the machine is running and the saw head is not in

the rest position

• Never cut workpieces shorter than 30 mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 90 mm by width 345 mm by length 600 mm

– Longer workpiece needs to be supported by suitable additional

table, e.g. DE7023. Always clamp the workpiece safely.

• In case of an accident or machine failure, immediately turn the machine

off and disconnect machine from the power source.

• Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the saw blade is blocked due to abnormal feed force during

cutting, turn the machine off and disconnect it from power supply.

Remove the workpiece and ensure that the saw blade runs free. Turn

the machine on and start new cutting operation with reduced feed

force.

• Never cut light alloy, especially magnesium.

• Whenever the situation allows, mount the machine to a bench using

bolts with a diameter of 8 mm and 80 mm in length (fig.j).

• Ensure the operator is adequately trained in the use, adjustment and

operation of the machine.

Residual Risks

The following risks are inherent to the use of saws:

- injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be avoided.

These are:

- Impairment of hearing.

- Risk of accidents caused by the uncovered parts of the rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ﬁ ngers when opening the guards.

- Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

The following factors increase the risk of breathing problems:

– No dust extractor connected when sawing wood.

– Insufficient dust extraction caused by uncleaned exhaust filters.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Carrying point

Keep hands away from blade.

DATE CODE POSITION (FIG. A1)

The Date Code (6), which also includes the year of manufacture, is printed

into the housing.

Example:

2010 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Assembled mitre saw

1 Blade spanner

1 Saw blade

1 Dustbag

1 LED Worklight System (DW718XPS)

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (ﬁ g A1 - A7)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

1 On/off switch

2 Moveable lower blade guard

3 Fence left-hand side

4 Mitre lever

5 Mitre latch

6 Date code

7 Mitre scale

8 Fence right-hand side

9 Kerf plate

10 Carrying handle

11 Operating handle

12 Head lock up release lever

13 Electronic speed control dial

14 Spindle lock

15 Bevel scale

16 Rail lock knob

17 Grooving stop

18 Dust spout

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW718XPS T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW718XPS T 4 Manual

Product: