Manual DeWalt DW717XPS T 4 (page 38 of 144) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546167

Zoom out

Zoom in

1/144

• Secure the material before cutting. Cut slowly through the material

using a out-down-and-back motion. Failure to clamp securely or cut

slowly could result in the material coming loose and causing injury.

After several cuts are made at various miter angles other than 0º, the

platform may weaken and not properly support the work. Install a new,

unused platform to the saw after presetting the desired miter angle.

WARNING: Continued use of a platform with several kerfs may

cause loss of material control and possible injury.

Dust extraction (ﬁ g. A2 & A3)

• Fit the dustbag (27) onto the dust spout (26).

WARNING! Whenever possible, connect a dust extraction

device designed in accordance with the relevant regulations

regarding dust emission.

Saw blades

To obtain the stated cutting capacities, always use 250 mm saw blades

with 30 mm arbor holes.

Transporting (ﬁ g. A1, A2 & B)

In order to conveniently carry the mitre saw, a carrying handle (10) has

been included on the top of the saw arm.

• To transport the saw, lower the head and depress the lock down pin (22).

• Lock the rail lock knob with the saw head in the front position, lock the

mitre arm in the full left mitre angle, slide the fence (3 & 8) completely

inward and lock the bevel lever (20) with the saw head in the vertical

position to make the tool as compact as possible.

• Always use the carrying handle (10) or the hand indentations (24)

shown in ﬁ g. B to transport the saw.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing

and removing accessories, before adjusting or changing

set-ups or when making repairs. Be sure the trigger switch

is in the OFF position. An accidental start-up can cause injury.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Before use, carefully check the upper blade guard, movable lower blade

guard as well as the dust extraction tube to determine that it will operate

properly. Ensure that chips, dust or workpiece particle cannot lead to

blockage of one of the functions.

In case of workpiece fragments jammed between saw blade and guards

disconnect the machine from the power supply and follow the instructions

given in section Mounting the Saw Blade. Remove the jammed parts and

reassembling the saw blade.

WARNING: Blow dirt and dust out of the main housing with dry

air as often as dirt is seen collecting in and around the air vents.

Wear approved eye protection and approved dust mask when

performing this procedure.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals

may weaken the materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool into a

liquid.

WARNING: To reduce the risk of injury, regularly clean the

table top.

WARNING: To reduce the risk of injury, regularly clean the

dust collection system.

WORKLIGHT CLEANING

• Carefully clean sawdust and debris from worklight lens with a cotton

swab. Dust build-up can block the worklight and prevent it from

accurately indicating the line of cut.

• DO NOT use solvents of any kind; they may damage the lens.

• With blade removed from saw, clean pitch and build-up from blade.

Optional Accessories (ﬁ g. A5, A6)

WARNING: Since accessories, other than those offered by

DEWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the

risk of injury, only DEWALT, recommended accessories should

be used with this product.

SAW BLADES: ALWAYS USE 250 mm SAW BLADES WITH 30 mm

ARBOUR HOLES. SPEED RATING MUST BE AT LEAST 4000 RPM.

Never use a smaller diameter blade. It will not be guarded properly.

Use crosscut blades only! Do not use blades designed for ripping,

combination blades or blades with hook angles in excess of 5°.

BLADE DESCRIPTIONS

APPLICATION DIAMETER TEETH

Construction Saw Blades (thin kerf with anti-stick rim)

General Purpose 250 mm 40

Fine Crosscuts 250 mm 60

Woodworking Saw Blades (provide smooth, clean cuts)

Fine crosscuts 250 mm 80

Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. This product must not be disposed of with

normal household waste.

Should you ﬁnd one day that your DEWALT product needs replacement, or

if it is of no further use to you, do not dispose of it with household waste.

Make this product available for separate collection.

Separate collection of used products and packaging allows

materials to be recycled and used again. Re-use of recycled

materials helps prevent environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection of electrical products

from the household, at municipal waste sites or by the retailer when you

purchase a new product.

DEWALT provides a facility for the collection and recycling of DEWALT

products once they have reached the end of their working life. To take

advantage of this service please return your product to any authorised repair

agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by

contacting your local DEWALT office at the address indicated in this manual.

Alternatively, a list of authorised DEWALT repair agents and full details

of our after-sales service and contacts are available on the Internet at:

www.2helpU.com.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW717XPS T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW717XPS T 4 Manual

Product: