Manual DeWalt DW717XPS T 4 (page 32 of 144) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

546167

Zoom out

Zoom in

1/144

• Do not use any abrasive or diamond discs.

• Never use your saw without the kerf plate.

• Raise the blade from the kerf in the workpiece prior to releasing the switch.

• Do not wedge anything against the fan to hold the motor shaft.

• The blade guard on your saw will automatically raise when the arm is

brought down; it will lower over the blade when head lock up release

lever (12) is pushed.

• Never raise the blade guard manually unless the saw is switched off.

The guard can be raised by hand when installing or removing saw

blades or for inspection of the saw.

• Check periodically that the motor air slots are clean and free of chips.

• Replace the kerf plate when worn.

• Disconnect the machine from the mains before carrying out any

maintenance work or when changing the blade.

• Never perform any cleaning or maintenance work when the machine is

still running and the head is not in the rest position.

• When possible, always mount the machine to a bench.

• If you use an LED to indicate the cutting line, make sure that the LED is

of class 2 according to EN 62471. Do not replace an LED diode with

a different type. If damaged, have the LED repaired by an authorised

repair agent.

• The front section of the guard is louvered for visibility while cutting.

Although the louvers dramatically reduce flying debris, they are

openings in the guard and safety glasses should be worn at all times

when viewing through the louvers.

• Connect the saw to a dust collection device when sawing wood.

Always consider factors which influence exposure of dust such as:

-– type of material to be machined (chip board produces more dust

than wood);

-– sharpness of the saw blade;

-– correct adjustment of the saw blade.

-– dust extractor with air velocity not less than 20 m/s.

Ensure that the local extraction as well as hoods, baffles and chutes are

properly adjusted.

• Please be aware of the following factors influencing exposure

to noise:

-– use saw blades designed to reduce the emitted noise;

-– use only well sharpened saw blades;

• Machine maintenance shall be conducted periodically;

• Provide adequate general or localized lighting;

• Ensure the operator is adequately trained in the use, adjustment and

operation of the machine;

• Ensure that any spacers and spindle rings are suitable for the purpose

as stated in this manual.

• Refrain from removing any cut-offs or other parts of the workpiece from

the cutting area while the machine is running and the saw head is not in

the rest position.

• Never cut workpieces shorter than 200 mm.

• Without additional support the machine is designed to accept the

maximum workpiece size of:

– Height 89 mm by width 302 mm by length 600 mm

– Longer workpieces need to be supported by suitable additional

table, e.g. DE7023. Always clamp the workpiece safely.

• In case of an accident or machine failure immediately turn the machine

off and pull the plug.

• Report the failure and mark the machine in suitable form to prevent

other people from using the defective machine.

• When the saw blade is blocked caused by abnormal feed force during

cutting, switch the machine off and disconnect from power supply.

Remove the workpiece and ensure that the saw blade runs free. Switch

the machine on and start new cutting operation with reduced feed

force.

• Never cut light alloy (i.e., aluminium, magnesium). It is not allowed for

this saw.

• Whenever the situation allows, mount the machine to a bench using

bolts with a diameter of 8 mm bolts and 80 mm in length.

Residual Risks

The following risks are inherent to the use of saws:

– injuries caused by touching the rotating parts

In spite of the application of the relevant safety regulations and the

implementation of safety devices, certain residual risks cannot be avoided.

These are:

– Impairment of hearing.

– Risk of accidents caused by the uncovered parts of the rotating saw

blade.

– Risk of injury when changing the blade.

– Risk of squeezing fingers when opening the guards.

– Health hazards caused by breathing dust developed when sawing

wood, especially oak, beech and MDF.

The following factors increase the risk of breathing problems:

– No dust extractor connected when sawing wood

– Insufficient dust extraction caused by uncleaned exhaust filters

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

Carrying point

Keep hands away from blade.

Do not stare directly into the light source.

DATE CODE POSITION (FIG. A1)

The Date Code (13), which also includes the year of manufacture, is printed

into the housing.

Example:

2013 XX XX

Year of Manufacture

Package Contents

The package contains:

1 Assembled mitre saw

1 Blade spanner

1 Saw blade

1 Dustbag

1 Material clamp

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (ﬁ g. A1–A6)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

1 On/off switch

2 Moveable lower blade guard

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW717XPS T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW717XPS T 4 Manual

Product: