Manual DeWalt DW712 T 3 (page 31 of 112) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545016

Zoom out

Zoom in

1/112

ENGLISH

Cutting Base Mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying flat on the

saw.

INSIDE CORNER

Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

OUTSIDE CORNER

Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Cutting Crown Mouldings

The cutting of crown moulding is performed in a compound mitre.

In order to achieve extreme accuracy, your saw has pre-set angle

positions at 31.62° mitre and 33.85° bevel. These settings are for

standard crown mouldings with 52° angles at the top and 38° angles

at the bottom.

• Make test cuts using scrap material before doing the final cuts.

• All cuts are made in a left bevel and with the back of the moulding

against the base.

INSIDE CORNER

Left side

• Top of the moulding against the fence.

• Mitre right.

• Save the left side of the cut.

0 5 10 15 20 25 30 35 40 45

SET THIS BEVEL ANGLE ON SAW

SET THIS MITER ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE"A")

SQUARE BOX

6 SIDED BOX

8 SIDED BOX

Right side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

OUTSIDE CORNER

Left side

• Bottom of the moulding against the fence.

• Mitre left.

• Save the left side of the cut.

Right side

• Top of the moulding against the fence.

• Mitre right.

• Save the right side of the cut.

GROOVING (FIG. T)

Your saw is equipped with a grooving stop (12) and grooving depth

adjustment knob (15) to allow for groove cutting.

• Flip the grooving stop (12) towards the front of the saw.

• Adjust the grooving depth adjustment knob (15) to set the depth of

the groove cut. It might be necessary to release the lock nut (66)

first.

• Place a piece of scrap material of approx. 5 cm between fence and

workpiece in order to perform a straight groove cut.

DUST EXTRACTION (FIG. A2 & A5)

This machine is provided with a dust extraction point (24) for connection

of a dust extraction kit (36) (available as an option).

• Whenever possible, connect a dust extraction device designed in

accordance with the relevant regulations regarding dust emission.

CUTTING SMALL PIECES (FIG. J1)

The upper part of the left side of the fence (3) can be adjusted to

provide maximum support when cutting small pieces.

• Put the saw blade into vertical position.

• Loosen the plastic knob (29) at least 3 full turns.

• Adjust the fence as close to the blade as possible.

• Tighten the knob securely.

SUPPORT FOR LONG PIECES (FIG. A4)

• Always support long pieces.

• For best results, use the extension work support (35) to extend the

table width of your saw (available from your dealer as an option).

Support long workpieces using any convenient means such as

saw-horses or similar devices to keep the ends from dropping.

SAW BLADES

To obtain the stated cutting capacities, always use 216 mm saw blades

with 30 mm arbor holes. Consult your dealer for further information on

the appropriate accessories.

TRANSPORTING (FIG. B2)

In order to conveniently carry the tool, a carrying strap can be attached

to the base. The carrying strap (see fig. A6) is available as an option.

• To transport the saw, lower the head and depress the lock down

pin (14).

• Lock the rail lock knob with the saw head in the front position, lock

the mitre arm in the right mitre angle, slide the fence (3) completely

inward and lock the bevel lever (11) with the saw head in the

vertical position to make the tool as compact as possible.

• Always use the hand indentations (30) shown in fig. B2 to transport

the saw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW712 T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW712 T 3 Manual

Product: