545015

DeWalt DW712 T 2 Manual

31
Zoom out
Zoom in
Previous page
1/124
Next page
31
ENGLISH
Mitre lock/detent rod adjustment (fig. H)
If the base of the saw can be moved while the mitre lever (4) is locked,
the mitre lock/detent rod (56) must be adjusted.
• Unlock the mitre lever (4).
• Fully tighten the mitre lock/detent rod (56) using a screwdriver (57).
Then loosen the rod a quarter of a turn.
• Check that the table does not move when the lever (4) is locked at a
random (not preset) angle.
Checking and adjusting the blade to the table (fig. I1 - I4)
• Loosen the bevel clamp handle (11).
• Press the saw head to the right to ensure it is fully vertical and tighten
the bevel clamp handle.
• Pull down the head until the blade just enters the saw kerf (51).
• Place a set square (52) on the table and up against the blade (47) (fig. I2).
Do not touch the tips of the blade teeth with the square.
• If adjustment is required, proceed as follows:
• Loosen the bevel clamp handle (11) and turn the vertical position
adjustment stop screw (28) in or out until the blade is at 90° to the
table as measured with the square.
• If the bevel pointer (58) does not indicate zero on the bevel scale (10),
loosen the screw (59) that secures the pointer and move the pointer as
necessary.
Adjusting the fence (fig. J)
The upper part of the left side of the fence can be adjusted to the left to provide
clearance, allowing the saw to bevel to a full 48° left. To adjust the fence (3):
• Loosen the plastic knob (29) and slide the fence to the left.
• Make a dry run with the saw switched off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and down
movement of the arm.
• Tighten the knob securely.
The guide groove (60) can become clogged with sawdust. Use
a stick or some low pressure air to clear the guide groove.
Overriding the bevel stops (fig. K)
The bevel stops facilitate the setting of the saw blade in the vertical
position and the 45° bevel position. By overriding the bevel stops, bevel
angles can be achieved from 2° right to 48° left.
• To override the bevel stops, first release the saw head and push it
slightly to the left, then pull out the override knob (27) and turn it into the
override position (62). The override knob automatically clicks in place.
• Set the required bevel angle and secure the head in this position.
• To discontinue the override, turn the override knob (27) back into the
bevel stop position (61).
Intermediate bevel stop
The intermediate bevel angle is preset at 33.85°, enabling a quick setting
for the cutting of crown moulding.
• To activate the intermediate bevel stop, turn the override knob (27) into
the intermediate bevel stop position (63).
Checking and adjusting the bevel angle (fig. A1, A2 & I5)
• Make sure the override knob (27) is located in the bevel stop position.
• Loosen the left side fence clamping knob (29) and slide the upper part
of the left side fence to the left as far as it will go.
• Loosen the bevel clamp handle (11) and move the saw head to the left.
This is the 45° bevel position.
• If adjustment is required, proceed as follows:
• Turn the stopscrew (9) in or out as necessary until the pointer (58)
indicates 45°.
Checking and adjusting the intermediate bevel angle (fig. A1, A2, & I6)
• Make sure the override knob (27) is located in the intermediate bevel
stop position.
• Loosen the left side fence clamping knob (29) and slide the upper part
of the left side fence to the left as far as it will go.
• Loosen the bevel clamp handle (11) and move the saw head to the left.
This is the 33.85° bevel position.
• If adjustment is required, proceed as follows:
• Turn the stopscrew (8) in or out as necessary until the pointer (58)
indicates 33.85°.
Rail guide adjustment (fig. L)
• Regularly check the rails for clearance.
• To reduce clearance, gradually rotate the set screw (64) clockwise
while sliding the saw head back and forth.
Instructions for use
• Always observe the safety instructions and applicable
regulations.
The attention of UK users is drawn to the “woodworking machines
regulations 1974” and any subsequent amendments.
Prior to operation:
• Install the appropriate saw blade. Do not use excessively worn blades.
The maximum rotation speed of the tool must not exceed that of the
saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
• Secure the workpiece.
• Although this saw will cut wood and many nonferrous materials, these
operating instructions refer to the cutting of wood only. The same
guide-lines apply to the other materials. Do not cut ferrous (iron and
steel) materials, fibre cement or masonry with this saw!
• Make sure to use the kerf plate. Do not operate the machine if the kerf
slot is wider than 10 mm.
Switching on and off (fig. M)
A hole (65) is provided in the trigger for insertion of a padlock to lock the
tool.
• To run the tool, press the on/off switch (1).
• To stop the tool, release the switch.
Setting the variable speed (fig. M)
The speed control dial (19) can be used for advance setting of the required
range of speed.
• Turn the dial button (19) to the desired range, which is indicated by a
number.
• Use high speeds for sawing soft materials such as wood. Use low
speeds for sawing metal.
Basic saw cuts
Vertical straight cross cut (fig. A1, A2 & N)
• Release the mitre lever (4) and depress the mitre latch (5).
• Engage the mitre latch at the 0° position and tighten the mitre lever.
• Place the wood to be cut against the fence (3 & 7).
• Take hold of the operating handle (18) and depress the head lock up
release lever (17) to release the head. Press the trigger switch (1) to
start the motor.
• Depress the head to allow the blade to cut through the timber and
enter the plastic kerf plate (31).
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW712 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW712 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info