Manual DeWalt DW711 T 5 (page 24 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

545011

Zoom out

Zoom in

1/100

english

– Risk of accidents caused by the uncovered parts of the rotating saw

blade.

– Risk of injury when changing the blade.

 – Riskofsqueezingfingerswhenopeningtheguards.

 – Healthhazardscausedbybreathingdustdevelopedwhensawing

wood,especiallyoak,beechandMDF.

The following factors are of influence to dust exposure:

~ worn saw blade

~ dust extractor with air velocity less than 20 m/s

~ workpiece not exactly guided

Markings on tool

The following pictograms are shown on the tool:

Read the instruction manual before use.

When using the machine in the mitre saw mode,

make sure that the upper part of the saw blade is

fully covered by the upper saw blade guard.

Only use the machine when the bench saw table is in

highest position.

When using the machine in the bench saw mode,

make sure that the upper and lower guards are in

place. Only use the machine when the bench saw

tableisinhorizontalposition.

Carrying point.

Package Contents

The package contains:

1 Assembled table top mitre saw

1 Parallel rip fence

1 Guard for bench saw position

1 Bottom guard for bench saw position

1 Push stick

1 Hex key 4/6 mm

1 Hex key 5 mm

1 Two-pin spanner

1 Dust extraction adapter for top guard

1 Instruction manual

1 Exploded drawing

 • Checkfordamagetothetool,partsoraccessorieswhichmay

have occurred during transport.

 • Takethetimetothoroughlyreadandunderstandthismanualpriorto

operation.

 • Removethesawfromthepackagingmaterialcarefully.

 • Releasetheheadlockdownknobtoraisetheheadofthemachine.

Description (ﬁg. A1–A5)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

1 On/off switch

2 Head lock up release lever

3 Additional saw bench table locking knob

4 Moveable lower blade guard

5 Fixed table

6 Blade slot

7 Mitre lever

8 Mitre latch

9 Rotating table/mitre arm

10 Mitre scale

11 Fence

12 Bevel clamp handle

13 Head lock down knob

14 Saw bench table

15 Riving knife

16 Upper saw blade guard

17 Rip fence

18 Fixed lower guard (for use in bench saw position)

19 Attachment mounting holes

OPTIONAL ACCESSORIES

20 Table end plate

21 Support guide rails

22 Material support plate

23 Material clamp

24 Swivelling stop

25 Adjustable stand 760 mm (max. height)

26 Legstand

27 Length stop for short workpieces (to be used with guide rails [21])

26 Legstand

29 Roller table

INTENDED USE

Your DW711 table top mitre saw has been developed for professional

applications. This high precision machine can be easily and quickly set to

crosscut, bevel, mitre, or compound mitre.

DO NOT use under wet conditions or in presence of flammable liquids or

gases.

These mitre saws are professional power tools.

DO NOT let children come into contact with the tool. Supervision is required

when inexperienced operators use this tool.

Electrical safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Machines in the scope of EN 61029 are not allowed for production use.

In case of cord replacement the tool must only be repaired by an authorized

service agent or by qualified electrician.

Mains Plug Replacement

(U.K. & Ireland Only)

DANGER:

 • Shouldyourmainsplugneedreplacingandyouarecompetentto

dothis,proceedasinstructedbelow.Ifyouareindoubt,contactan

authorizedDeWALT repair agent or a qualified electrician.

 • Disconnecttheplugfromthesupply.

 • Cutoffthepluganddisposeofitsafely;aplugwithbaredcopper

conductors is dangerous if engaged in a live socket outlet.

 • Onlyfit13AmperesBS1363Aapprovedplugsfittedwiththecorrectly

rated fuse (1).

 • Thecablewirecolours,oraletter,willbemarkedattheconnection

points of most good quality plugs. Attach the wires to their respective

points in the plug (see below). Brown is for Live (L) (2) and Blue is for

Neutral (N) (4).

 • Beforereplacingthetopcoverofthemainsplugensurethatthecable

restraint (3) is holding the outer sheath of the cable firmly and that the

two leads are correctly fixed at the terminals crews.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW711 T 5 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW711 T 5 Manual

Product: