Manual DeWalt DW705 T 4 (page 25 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544979

Zoom out

Zoom in

1/116

ENGLISH

19 en - 2

Safety instructions

When using Power Tools, always observe the safety regulations

applicable in your country to reduce the risk of fire, electric shock

and personal injury. Read the following safety instructions before

attempting to operate this product.

Keep these instructions in a safe place!

General

1 Keep work area clean

Cluttered areas and benches can cause accidents.

2 Consider work area environment

Do not expose Power Tools to humidity. Keep work area well lit.

Do not use Power Tools in the presence of inflammable liquids or gases.

3 Guard against electric shock

Prevent body contact with earthed surfaces (e.g. pipes, radiators,

cookers and refrigerators).

For use under extreme conditions (e.g. high humidity, when metal

swarf is being produced, etc.) electric safety can be improved by

inserting an isolating transformer or a (FI) earth-leakage circuit-breaker.

4 Keep children away

Do not let children come into contact with the tool or extension cord.

Supervision is required for those under 16 years of age.

5 Extension cords for outdoor use

When the tool is used outdoors, always use extension cords intended

for outdoor use and marked accordingly.

6 Store idle tools

When not in use, Power Tools must be stored in a dry place and

locked up securely, out of reach of children.

7 Dress properly

Do not wear loose clothing or jewellery. They can be caught in moving

parts. Preferably wear non-slip footwear when working outdoors.

Wear protective hair covering to keep long hair out of the way.

8 Wear safety goggles

Also use a face or dust mask in case the operations produce dust or

flying particles.

9 Beware of maximum sound pressure

Take appropriate measures for the protection of hearing if the sound

pressure of 85 dB(A) is exceeded.

10 Secure workpiece

Use clamps or a vice to hold the workpiece. It is safer and it frees both

hands to operate the tool.

11 Do not overreach

Keep proper footing and balance at all times.

12 Avoid unintentional starting

Do not carry the plugged-in tool with a finger on the switch.

Be sure that the switch is released when plugging in.

13 Stay alert

Watch what you are doing. Use common sense. Do not operate the

tool when you are tired.

14 Disconnect tool

Shut off power and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use, before

servicing or changing accessories.

15 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

16 Use appropriate tool

The intended use is laid down in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool.

The tool will do the job better and safer at the rate for which it was

intended.

Warning! The use of any accessory or attachment or performance of

any operation with this tool, other than those recommended in this

instruction manual may present a risk of personal injury.

17 Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the socket.

Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Inspect the tool cords at regular intervals and,

if damaged, have them repaired by an authorized DEWALT repair

agent. Inspect the extension cords periodically and replace them if

damaged. Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts

Before using the tool, carefully check it for damage to ensure that it will

operate properly and perform its intended function.

Check for misalignment and seizure of moving parts, breakage of parts

and any other conditions that may affect its operation. Have damaged

guards or other defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. Have the switch replaced

by an authorized DEWALT repair agent.

20 Have your tool repaired by an authorized DEWALT repair agent

This Power Tool is in accordance with the relevant safety regulations.

To avoid danger, electric appliances must only be repaired by qualified

technicians.

Additional Safety Rules for Mitre Saws

21 Guard actuation

The blade guard on your saw will automatically raise when the arm is

brought down; it will lower over the blade when the arm is raised.

The guard can be raised by hand when installing or removing saw

blades or for inspection of the saw. Never raise the blade guard

manually unless the saw is turned OFF.

22 Flying debris

The front section of the guard is louvred for visibility while cutting.

Although the louvres dramatically reduce flying debris, there are

openings in the guard and safety glasses should be worn at all times

when viewing through the louvres.

23 Saw blades

Make sure that the blade rotates in the correct direction. Keep the

blade sharp. Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the technical data.

24 Blade guards

Never operate the saw without the guards in place.

25 Mind your hands

Keep your hands out of the path of the saw blade. Never place them in

the blade area when the saw is connected to the electrical power source.

26 Stopping the motor

Raise the blade from the kerf in the workpiece prior to releasing the

switch. Never attempt to stop the machine in motion by jamming a tool

or similar against the blade. Do not wedge anything against the fan to

hold the motor shaft.

27 Maintenance of the blade and the arbor collars

Make sure that the blade and the arbor collars are clean on the

surfaces of contact and use both wrenches to tighten.

Electrical safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in accordance with

EN 50144; therefore no earth wire is required.

Mains plug replacement (U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

authorized DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

Cual es la pieza o como se llama. Donde acopla la hoja de sierra Submitted on 8-1-2022 at 00:55
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW705 T 4 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW705 T 4 Manual

Product: