544975

DeWalt DW705 T 2 Manual

26
Zoom out
Zoom in
Previous page
1/116
Next page
en - 3 20
ENGLISH
• Press down the operating handle (1) and pull out the lock down pin (28),
as shown in fig. A2.
• Gently release the downward pressure and allow the arm to rise to its
full height.
Description (fig. B1 - B3)
B1
1 Operating handle
2 Moveable lower guard
3 Fence right-hand side
4 Mitre clamp knob
5 Mitre latch
6 Mitre scale
7 Fence left-hand side
8 Bench mounting holes
9 Carrying handle
10 Head lock up release lever
11 Rear lower guard
12 Bevel scale (DW705 only)
13 Padlock hole
14 Motor housing
15 Spindle lock button
16 Brush inspection cap
17 Trigger switch
B2
18 Blade spanner
19 Angle position stop (DW705 only)
20 Dust spout
21 Bevel clamp handle (DW705 only)
22 Hand indentation
23 Upper fence left-hand side clamping knobs (DW705 only)
24 Upper guard
25 Vertical position adjustment stop (DW705 only)
26 Bevel position adjustment stop (DW705 only)
27 Kerf plate
28 Head lock down pin
B3
29 Work support extension
30 Adjustable length stop
31 Work piece clamp
32 Dustbag
Assembly
Prior to assembly always unplug the tool.
The motor and guards are already assembled onto the base.
Bench Mounting (fig. C1 & C2)
• Holes (8) are provided in all four feet to facilitate bench mounting.
Two different sized holes are provided to accommodate different sizes
of bolts (33). Use either hole; it is not necessary to use both.
Always mount your saw firmly to prevent movement. To enhance the
portability, the tool can be mounted to a piece of 12.5 mm or thicker
plywood which can then be clamped to your work support or moved to
other job sites and reclamped.
• When mounting your saw to a piece of plywood, make sure that the
mounting screws do not protrude from the bottom of the wood.
The plywood must sit flush on the work support. When clamping the
saw to any work surface, clamp only on the clamping bosses where
the mounting screw holes are located. Clamping at any other point will
interfere with the proper operation of the saw.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or .
For 115 V tools, use plugs to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved triple-core extension
cable suitable for the power input of this tool (see technical data).
The minimum conductor size is 1.5 mm
2
.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0-2.0 66 6666
2.1-3.4 66 6666
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Unpacking (fig. A1 & A2)
Remove the saw from the packing material carefully using the carrying
handle (9).
The package contains:
1 Assembled Mitre Saw
1 Blade spanner
1 305 mm TCT saw blade
2 Clamps (DW704 only)
1 Instruction manual
1 Exploded drawing
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DeWalt DW705 T 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW705 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info