Manual DeWalt DW703 T 2 (page 28 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544967

Zoom out

Zoom in

1/108

ENGLISH

en - 5 20

Adjusting the fence (fig. H)

The upper part of the left side of the fence (7) can be adjusted to the left to

provide clearance, allowing the saw to bevel to a full 48° left. To adjust the

fence:

• Loosen the plastic knob (23) and slide the fence to the left.

• Make a dry run with the saw switched off and check for clearance.

Adjust the fence to be as close to the blade as practical to provide

maximum workpiece support, without interfering with the up and down

movement of the arm.

• Tighten the knob securely.

The guide groove (52) can become clogged with sawdust. Use

a stick or some low pressure air to clear the guide groove.

Checking and adjusting the bevel angle (fig. A1, A2, I1 & I2)

• Loosen the left side fence clamping knob (23) and slide the upper part

of the left side fence to the left as far as it will go.

• Loosen the bevel clamp handle (17) and move the saw arm to the left

until the angle position stop (21) rests on the bevel position adjustment

stop (26). This is the 45° bevel position.

• If adjustment is required, proceed as follows:

• Loosen the lock nut (53) a few turns and turn the bevel position

adjustment stop screw (26) in or out until the pointer (54) indicates 45°

with the angle position stop (21) resting on the bevel position

adjustment stop.

• Firmly tighten the lock nut (53) while holding the stop screw (26)

stationary.

• To achieve a 3° right bevel or a 48° left bevel, the two adjustment stop

screws must be adjusted to allow the saw arm to move as necessary.

Instructions for use

• Always observe the safety instructions and applicable

regulations.

The attention of UK users is drawn to the “woodworking machines

regulations 1974” and any subsequent amendments.

Prior to operation:

• Install the appropriate saw blade. Do not use excessively worn blades.

The maximum rotation speed of the tool must not exceed that of the

saw blade.

• Do not attempt to cut excessively small pieces.

• Allow the blade to cut freely. Do not force.

• Allow the motor to reach full speed before cutting.

• Make sure all locking knobs and clamp handles are tight.

• Secure the workpiece.

• Although this saw will cut wood and many nonferrous materials,

these operating instructions refer to the cutting of wood only. The same

guide-lines apply to the other materials. Do not cut ferrous (iron and

steel) materials or masonry with this saw! Do not use any abrasive discs!

• Make sure to use the kerf plate. Do not operate the machine if the kerf

slot is wider than 10 mm.

Switching on and off (fig. J)

• To switch the tool on, depress the trigger switch (16).

• To stop the tool, release the switch.

• There is no provision for locking the switch on, but a hole (13) is

provided in the trigger for insertion of a padlock to lock the tool off.

Vertical straight cross cut (fig. A1, A2 & K)

• Loosen the mitre clamp knob (4) and squeeze the mitre latch (5) upwards.

• Engage the mitre latch at the 0° position and tighten the mitre clamp

knob.

• Place the wood to be cut against the fence (3 & 7).

• Take hold of the operating handle (1) and depress the head lock up

release lever (10) to release the head. Press the trigger switch (17) to

start the motor.

• Depress the head to allow the blade to cut through the timber and

enter the plastic kerf plate (27).

• After completing the cut, release the switch and wait for the saw blade

to come to a complete standstill before returning the head to its upper

rest position.

Vertical mitre cross-cut (fig. L)

• Loosen the mitre clamp knob and squeeze the mitre latch upwards.

Move the head left or right to the required angle.

• The mitre latch will automatically locate at 10°, 15°, 22.5°, 31.62° and

45°. If any intermediate angle or 50° is required hold the head firmly

and lock by tightening the mitre clamp knob.

• Always ensure that the mitre clamp knob is locked tightly before cutting.

• Proceed as for a vertical straight cross-cut.

When mitring the end of a piece of wood with a small off-cut,

position the wood to ensure that the off-cut is to the side of

the blade with the greater angle to the fence; i.e. left mitre,

off-cut to the right - right mitre, off-cut to the left.

Bevel cuts (fig. A1, A2 & M)

Bevel angles can be set from 3° right to 48° left and can be cut with the mitre

arm set between zero and a maximum of 45° mitre position right or left.

• Loosen the left side fence clamping knob (23) and slide the upper part

of the left side fence (7) to the left as far as it will go. Loosen the bevel

clamp handle (17) and set the bevel as desired.

• Tighten the bevel clamp handle (17) firmly.

• Proceed as for a vertical straight cross-cut.

Quality of cut

The smoothness of any cut depends on a number of variables, e.g. the

material being cut. When smoothest cuts are desired for moulding and

other precision work, a sharp (60 tooth carbide) blade and a slower, even

cutting rate will produce the desired results.

Ensure that the material does not creep while cutting; clamp it

securely in place. Always let the blade come to a full stop

before raising the arm. If small fibres of wood still split out at

the rear of the workpiece, stick a piece of masking tape on the

wood where the cut will be made. Saw through the tape and

carefully remove tape when finished.

Body and hand position

Proper positioning of your body and hands when operating the mitre saw

will make cutting easier, more accurate and safer.

• Never place your hands near the cutting area.

• Place your hands no closer than 150 mm from the blade.

• Hold the workpiece tightly to the table and the fence when cutting.

Keep your hands in position until the switch has been released and the

blade has completely stopped.

• Always make dry runs (without power) before finish cuts so that you

can check the path of the blade.

• Do not cross your hands.

• Keep both feet firmly on the floor and maintain proper balance.

• As you move the saw arm left and right, follow it and stand slightly to

the side of the saw blade.

• Sight through the guard louvres when following a pencil line.

Clamping the workpiece (fig. A5)

• Whenever possible, clamp the wood to the saw.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW703 T 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW703 T 2 Manual

Product: