Manual DeWalt DW682K T 3 (page 20 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish)

546682

Zoom out

Zoom in

1/64

ENGLISH

en - 2 12

11 Do not overreach

Keep proper footing and balance at all times.

12 Avoid unintentional starting

Do not carry the plugged-in tool with a finger on the switch.

Be sure that the switch is released when plugging in.

13 Stay alert

Watch what you are doing. Use common sense. Do not operate the

tool when you are tired.

14 Disconnect tool

Shut off power and wait for the tool to come to a complete standstill

before leaving it unattended. Unplug the tool when not in use,

before servicing or changing accessories.

15 Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches are removed from the

tool before operating the tool.

16 Use appropriate tool

The intended use is described in this instruction manual. Do not force

small tools or attachments to do the job of a heavy-duty tool. The tool

will do the job better and safer at the rate for which it was intended.

Warning! The use of any accessory or attachment or performance of

any operation with this tool, other than those recommended in this

instruction manual may present a risk of personal injury.

17 Do not abuse cord

Never carry the tool by its cord or pull it to disconnect from the socket.

Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care

Keep the tools in good condition and clean for better and safer

performance. Follow the instructions for maintenance and changing

accessories. Inspect the tool cords at regular intervals and,

if damaged, have them repaired by an authorized DEWALT repair

agent. Inspect the extension cords periodically and replace them if

damaged. Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts

Before using the tool, carefully check it for damage to ensure that it will

operate properly and perform its intended function. Check for

misalignment and seizure of moving parts, breakage of parts and any

other conditions that may affect its operation. Have damaged guards

or other defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. Have the switch replaced

by an authorized DEWALT repair agent.

20 Have your tool repaired by an authorized DEWALT repair agent

This Power Tool is in accordance with the relevant safety regulations.

To avoid danger, electric appliances must only be repaired by qualified

technicians.

Additional safety rules for biscuit jointers

Plugging into the mains, switching ON and OFF

• Always ensure that the power tool is switched OFF before plugging into

the mains.

• Do not switch OFF before the blade is running freely.

When cutting

• Remove all nails and metal objects from the workpiece before starting

work.

• After switching OFF, never attempt to stop the blade by pressing

against the side of the blade.

• Never put the tool down on a table or workbench unless switched OFF.

Operational protection devices

• The tool must only be used for cutting wood or plastic.

• Ensure that all devices screening the blade are in perfect working order.

Checking and changing the blade

• Only blades conforming to the specifications contained in these

operating instructions may be used.

• Blades made of high alloy, high speed steel (HSS steel) should not be

used. Best results are achieved using carbide-tipped or CrV blades.

• Only sharp blades in perfect working order should be used; cracked or

bent blades should be discarded and replaced at once.

• Ensure that the blade is securely fixed and rotates in the correct direction.

Guard against kickback

• Kickback occurs when the tool begins to stall rapidly and is driven

back towards the operator. Release the switch immediately if the blade

sticks or the tool stalls.

• Keep the blades sharp.

• Support large panels near the cutting area.

• Do not remove the tool from the workpiece while making a cut with the

blade rotating. Release the ON/OFF-switch and wait for the blade to

come to a halt.

Package contents

The package contains:

1 Biscuit jointer

1 Dust bag

2 Dust adapters

1 Pin spanner

1 Torx screwdriver

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories which may have

occurred during transport.

• Take the time to thoroughly read and understand this manual prior to

operation.

Description (fig. A)

Your DEWALT biscuit jointer DW682K has been designed for making flat

dowel joints in wood and wood products.

1 ON/OFF-switch

2 Lock-on button

3 Top handle

4 Fence height adjuster

5 Dust extraction outlet

6 Adjustable fence

7 Anti-slipping pins

8 Plunge depth adjusting knob

9 Locking knob

10 Spindle lock

11 Star knob

Electrical safety

The electric motor has been designed for one voltage only. Always check

that the power supply corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in accordance with

EN 50144; therefore no earth wire is required.

Mains plug replacement (U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do

this, proceed as instructed below. If you are in doubt, contact an

authorized DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug with bared copper

conductors is dangerous if engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly

rated fuse (1).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DeWalt DW682K T 3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of DeWalt DW682K T 3

DeWalt DW682K T 3 User Manual - Polish - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DeWalt DW682K T 3 Manual

Product: